홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Hydrochloric Acid → 4,4'-(Cyclopenta-2,4-dien-1-ylidenemethylene)bis(methylbenzene)

HRID 746977
인쇄

반응식

HRID 746977 반응식
[CH3:1][C:2]1[CH:16]=[CH:15][C:5]([C:6]([C:8]2[CH:13]=[CH:12][C:11]([CH3:14])=[CH:10][CH:9]=2)=O)=[CH:4][CH:3]=1.O1CCCC1.[CH:22]1([Na])[CH:26]=[CH:25][CH:24]=[CH:23]1.Cl>O.C(OCC)C>[C:11]1([CH3:14])[CH:12]=[CH:13][C:8]([C:6]([C:5]2[CH:15]=[CH:16][C:2]([CH3:1])=[CH:3][CH:4]=2)=[C:25]2[CH:24]=[CH:23][CH:22]=[CH:26]2)=[CH:9][CH:10]=1
참가 물질실험 절차후처리출처 및 근거반응 노트

참가 물질

7

반응물 4

HCID 313Hydrochloric AcidHCID 8028Tetrahydrofuran2회HCID 691484,4'-DimethylbenzophenoneHCID 178507085HCID 178507085, 화합물

생성물 1

HCID 124276304,4'-(Cyclopenta-2,4-dien-1-ylidenemethylene)bis(methylbenzene)수율 74.5%

시약·촉매·용매 2

HCID 962
Water
용매
HCID 3283Diethyl Ether용매

실험 절차

A 200 ml two-necked flask equipped with a dropping funnel, a magnetic stirrer and a three-way cock, was purged thoroughly with nitrogen. Into the flask, 4,4′-dimethylbenzophenone 6.72 g (31.9 mmol) was introduced, and dehydrated tetrahydrofuran 30 ml was further added. With cooling in an ice bath, 2 mol/L tetrahydrofuran solution of cyclopentadienyl sodium, 19.0 ml (38.0 mmol), was dropwise added to the flask. The contents were stirred at room temperature in a nitrogen atmosphere for 6 days to obtain a solution. With the flask cooled in an ice bath, 1 N hydrochloric acid aqueous solution 100 ml and diethyl ether 100 ml were gradually added in this order. The resulting two-phase solution was poured into a 300 ml separation funnel, and the funnel was shaken several times so that the water phase was removed. The obtained organic phase was washed twice with water 100 ml and once with a saturated salt solution 100 ml, and dried over anhydrous magnesium sulfate. The solution was filtered to remove solids, and the solvent of the filtrate was distilled away to obtain a red oily matter 9.40 g. The oily matter was subjected to silica gel chromatography to obtain 6.15 g of 6,6-di-p-tolyl fulvene as a red solid (23.8 mmol, 74.5% yield). Identification of the 6,6-di-p-tolyl fulvene was made by 1H NMR, the results being given below:

후처리

  1. customA 200 ml two-necked flask equipped with a dropping funnel, a magnetic stirrer
  2. customa three-way cock, was purged thoroughly with nitrogen
  3. temperatureWith cooling in an ice bath
  4. customto obtain a solution
  5. temperatureWith the flask cooled in an ice bath
  6. additionThe resulting two-phase solution was poured into a 300 ml separation funnel
  7. customwas removed
  8. washThe obtained organic phase was washed twice with water 100 ml and once with a saturated salt solution 100 ml
  9. dry with materialdried over anhydrous magnesium sulfate
  10. filtrationThe solution was filtered
  11. customto remove solids
  12. distillationthe solvent of the filtrate was distilled away
  13. customto obtain a red oily matter 9.40 g

출처 및 근거

ORD 기록
ord-c9e334f2460042399e68e756720a0f93
출처 데이터셋
uspto-grants-2008_07
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US07393965B2

반응 노트

이 페이지에서참가 물질실험 절차후처리출처 및 근거반응 노트