홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Hydrochloric Acid → 9a-butyl-8-chloro-4-ethyl-6-fluoro-7-methoxy-1,2,9,9a-tetrahydro-3H-fluoren-3-one

HRID 7897
인쇄

반응식

HRID 7897 반응식
C(C(CCC)=O)=C.N12CCCN=C1CCCCC2.C[O-].[Na+].CO.[CH2:24]([C:28]1([CH2:42][CH2:43][C:44](=[O:48])[CH2:45][CH2:46][CH3:47])[CH2:36][C:35]2[C:30](=[CH:31][C:32]([F:40])=[C:33]([O:38][CH3:39])[C:34]=2[Cl:37])[C:29]1=O)[CH2:25][CH2:26][CH3:27].Cl>O1CCCC1.C(O)(=O)C>[CH2:24]([C:28]12[CH2:42][CH2:43][C:44](=[O:48])[C:45]([CH2:46][CH3:47])=[C:29]1[C:30]1[C:35](=[C:34]([Cl:37])[C:33]([O:38][CH3:39])=[C:32]([F:40])[CH:31]=1)[CH2:36]2)[CH2:25][CH2:26][CH3:27]
참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트

참가 물질

9

반응물 6

HCID 313Hydrochloric AcidHCID 887MethanolHCID 153951-Hexen-3-oneHCID 811841,8-Diazabicyclo(5.4.0)undec-7-eneHCID 10942334Sodium MethoxideHCID 219908892-Butyl-4-chloro-6-fluoro-5-methoxy-2-(3-oxohexyl)-1-indanone

생성물 1

HCID 21990935
9a-butyl-8-chloro-4-ethyl-6-fluoro-7-methoxy-1,2,9,9a-tetrahydro-3H-fluoren-3-one

시약·촉매·용매 2

HCID 176Acetic Acid용매HCID 8028Tetrahydrofuran용매

반응 조건

온도
60 °C

실험 절차

A sample of the crude product from step 2 in the preceding example (386 mg, 1.36 mmol) in anhydrous tetrahydrofuran (2.7 mL) was treated with propyl vinyl ketone (0.188 mL, 1.63 mmol) and 1,8-diazabicyclo[5.4.0]undec-7-ene (0.041 mL, 0.272 mmol). The mixture was stirred and heated in an oil bath at 60° C. for two hours. TLC showed very little reaction. The mixture was treated with 0.5M sodium methoxide in methanol (0.54 mL, 0.272 mmol) and then stirred with heating at 60° C. for an additional 16.3 hours. After cooling to room temperature, the solvent was evaporated under vacuum to give a residue consisting mainly of 2-butyl-4-chloro-6-fluoro-5-methoxy-2-(3-oxohexyl)-1-indanone. This material was dissolved in acetic acid (6 mL), treated with aqueous 6N HCl (3 mL), and stirred while heating in an oil bath at 80° C. for 22.3 hours. After cooling, the mixture was partitioned between EtOAc (150 mL) and water (150 mL). The organic phase was washed with aqueous K2CO3 (100 mL) and brine (50 mL), dried over MgSO4, filtered, and evaporated under vacuum to an oil (420 mg). The crude product was purified by preparative layer chromatography on four 0.1×20×20 cm silica gel GF plates, developing three times with 10% EtOAc in hexanes. The product bands were combined, eluted with EtOAc, and the eluent evaporated under vacuum to give 9a-butyl-8-chloro-4-ethyl-6-fluoro-7-methoxy-1,2,9,9a-tetrahydro-3H-fluoren-3-one as an oil (153 mg). The product contained trace amounts of 9a-butyl-6-chloro-4-ethyl-8-fluoro-7-methoxy-1,2,9,9a-tetrahydro-3H-fluoren-3-one as evidenced by 1H NMR spectroscopy.

후처리

  1. customreaction
  2. stirringstirred
  3. temperaturewith heating at 60° C. for an additional 16.3 hours
  4. temperatureAfter cooling to room temperature
  5. customthe solvent was evaporated under vacuum
  6. customto give a residue
  7. stirringstirred
  8. temperaturewhile heating in an oil bath at 80° C. for 22.3 hours
  9. temperatureAfter cooling
  10. customthe mixture was partitioned between EtOAc (150 mL) and water (150 mL)
  11. washThe organic phase was washed with aqueous K2CO3 (100 mL) and brine (50 mL)
  12. dry with materialdried over MgSO4
  13. filtrationfiltered
  14. customevaporated under vacuum to an oil (420 mg)
  15. customThe crude product was purified by preparative layer chromatography on four 0.1×20×20 cm silica gel GF plates
  16. washeluted with EtOAc
  17. customthe eluent evaporated under vacuum

출처 및 근거

ORD 기록
ord-325295534468402fb193b69d30d93a94
출처 데이터셋
uspto-grants-2006_08
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US07087599B2

반응 노트

이 페이지에서참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트