홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Potassium Carbonate → 4,4-Dimethyl-2-(1-oxo-1,3-dihydroisobenzofuran-5-yl)oxazoline

HRID 840348
인쇄

반응식

HRID 840348 반응식
S(Cl)(Cl)=O.[C:5]([C:8]1[CH:9]=[C:10]2[C:15](=[CH:16][CH:17]=1)[C:13](=[O:14])[O:12][CH2:11]2)([OH:7])=O.C(=O)([O-])[O-].[K+].[K+].[NH2:24][C:25]([CH3:29])([CH3:28])[CH2:26]O>O1CCCC1.O.C1(C)C=CC=CC=1.CN(C)C(=O)C>[CH3:26][C:25]1([CH3:29])[CH2:28][O:7][C:5]([C:8]2[CH:9]=[C:10]3[C:15](=[CH:16][CH:17]=2)[C:13](=[O:14])[O:12][CH2:11]3)=[N:24]1
참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트

참가 물질

9

반응물 4

HCID 11430Potassium CarbonateHCID 118072-Amino-2-methyl-1-propanolHCID 24386Thionyl Chloride2회HCID 785171,3-Dihydro-1-oxoisobenzofuran-5-carboxylic acid

생성물 1

HCID 113221954,4-Dimethyl-2-(1-oxo-1,3-dihydroisobenzofuran-5-yl)oxazoline수율 59.8%

시약·촉매·용매 4

HCID 962
Water
용매
HCID 1140Toluene용매
HCID 8028Tetrahydrofuran용매3회
HCID 31374Dimethylacetamide용매

반응 조건

온도
60 °C

실험 절차

To a mixture of thionyl chloride (25 ml, 0.344 mol) and N,N-dimethylacetamide (0.2 ml), 5-carboxyphthalide (5 g, 0.028 mol) is added. The stirred mixture is heated 30 minutes at 60° C. and is then brought to reflux (about 80° C.) and kept under these conditions for 6 hours. The thionyl chloride is distilled off in vacuo to an inner temperature of about 90° C. The concentrated mixture is taken up with toluene (25 ml) and distilled in vacuo leaving a residue, which is taken up again twice with of toluene (10 ml) followed by concentration of the solution. The residual acid chloride is taken up with of tetrahydrofuran (25 ml) and the mixture is heated at 60° C. until a complete dissolution is obtained. The solution of the acid chloride in tetrahydrofuran is added dropwise to a mixture of micronized anhydrous potassium carbonate (5 g, 0.036 mol), 2-amino-2-methyl-1-propanol (3.06 ml, 0.032 mol) and of tetrahydrofuran (15 ml), cooled to about 0° C., keeping the temperature at 5-10° C. After about 30 minutes under these conditions, a control by HPLC is performed in order to verify the complete amide formation. The mixture is cooled to 0-3° C. and of thionyl chloride (2 ml, 0.027 mol) is added dropwise to the mixture. At the end of the addition, a control by HPLC confirms that the ring closure of the amide is completed. To the mixture, 50 ml of deionized water is slowly added at 5-10° C. The organic solvents are distilled off in vacuo and the pH is adjusted to 5 with 25% ammonia. The mixture is heated one hour at 50° C., then its temperature is let to decrease to about 20° C., kept at this value for 2 hours, then lowered to 10-15° C. and the mixture is maintained under these conditions for one hour. The mixture is dispersed by stirring, then it is filtered, washed with water and dried in vacuo at 40° C. Yield: 3.87 g of product. Total yield: 59.8%.

후처리

  1. additionis added
  2. temperatureto reflux (about 80° C.)
  3. distillationThe thionyl chloride is distilled off in vacuo to an inner temperature of about 90° C
  4. distillationdistilled in vacuo
  5. customleaving a residue, which
  6. temperaturethe mixture is heated at 60° C. until a complete dissolution
  7. customis obtained
  8. temperaturecooled to about 0° C.
  9. customat 5-10° C
  10. waitAfter about 30 minutes under these conditions
  11. additionis added dropwise to the mixture
  12. additionAt the end of the addition
  13. distillationThe organic solvents are distilled off in vacuo
  14. temperatureThe mixture is heated one hour at 50° C.
  15. customto decrease to about 20° C.
  16. waitkept at this value for 2 hours
  17. customlowered to 10-15° C.
  18. temperaturethe mixture is maintained under these conditions for one hour
  19. additionThe mixture is dispersed
  20. filtrationit is filtered
  21. washwashed with water
  22. customdried in vacuo at 40° C

출처 및 근거

ORD 기록
ord-0cfe51911b924fcba301cb7e25dbe69d
출처 데이터셋
uspto-grants-2002_04
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US06365747B1

반응 노트

이 페이지에서참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트