反应详情
EQUATION
反应方程式
REACTANTS
反应物
PRODUCTS
生成物
AUXILIARIES
试剂、催化剂与溶剂
CONDITIONS
反应条件
- 温度
- 80 °C
PROCEDURE
实验过程
A solution of (S)-tert-butyl 2-(5-(6-(4,4,5,5-tetramethyl-1,3,2-dioxaborolan-2-yl)naphthalen-2-yl)-1H-imidazol-2-yl)pyrrolidine-1-carboxylate (402 mg, 0.821 mmol), (S)-tert-butyl 2-(7-bromo-4,5-dihydro-1H-naphtho[1,2-d]imidazol-2-yl)pyrrolidine-1-carboxylate (344 mg, 0.821 mmol) and sodium bicarbonate (207 mg, 2.46 mmol) in DME (14 mL) and water (1.8 mL) was degassed under vacuum for 10 min. The mixture was heated at 80° C. at which time the flask was opened and Pd(Ph3P)4 (76 mg, 0.066 mmol) was added. The flask was flushed with nitrogen, sealed and heated at 120° C. for 16 h. The flask was cooled to room temp., the DME was removed in vacuo and the crude material was partitioned between DCM and H2O. The layers were separated and the aqueous layer was extracted several times with DCM. The combined organic extracts were dried over Na2SO4 and evaporated in vacuo. The residue was purified by flash column chromatography (BIOTAGE®), eluting with a gradient of 20 to 100% EtOAc/Hexanes and then 0 to 10% methanol/DCM to afford (S)-tert-butyl 2-(7-(6-(2-((S)-1-(tert-butoxycarbonyl)pyrrolidin-2-yl)-1H-imidazol-5-yl)naphthalen-2-yl)-4,5-dihydro-1H-naphtho[1,2-d]imidazol-2-yl)pyrrolidine-1-carboxylate (183 mg). LC-MS retention time 1.543 min; m/z 701.47 (MH+). LC data was recorded on a Shimadzu LC-10AS liquid chromatograph equipped with a Waters Sunfire 5u C18 4.6×30 mm column using a SPD-10AV UV-Vis detector at a detector wave length of 220 nM. The elution conditions employed a flow rate of 4 mL/min, a gradient of 100% Solvent A/0% Solvent B to 0% Solvent A/100% Solvent B, a gradient time of 2 min, a hold time of 1 min, and an analysis time of 3 min where Solvent A was 10% MeOH/90% H2O/0.1% TFA and Solvent B was 10% H2O/90% MeOH/0.1% TFA. MS data was determined using a MICROMASS® Platform for LC in electrospray mode.
WORKUP
后处理
- customThe flask was flushed with nitrogen
- customsealed
- temperatureheated at 120° C. for 16 h
- temperatureThe flask was cooled to room temp.
- customthe DME was removed in vacuo
- customthe crude material was partitioned between DCM and H2O
- customThe layers were separated
- extractionthe aqueous layer was extracted several times with DCM
- dry with materialThe combined organic extracts were dried over Na2SO4
- customevaporated in vacuo
- customThe residue was purified by flash column chromatography (BIOTAGE®)
- washeluting with a gradient of 20 to 100% EtOAc/Hexanes