StartseiteMCPWorkbenchSkills
StartseiteWorkbenchBenachrichtigungenMein Bereich
llms.txt · MCP-AnleitungDatenschutz · Nutzungsbedingungen · Supportv1.8.3
  1. Startseite
  2. /Reaktion

Phosphoric Acid → Nitrate

HRID 128900
Drucken

Reaktionsgleichung

Reaktionsgleichung von HRID 128900
[O-:1][Mo:2]([O-:5])(=[O:4])=[O:3].OP(O)(O)=O.[N+:11]([O-:14])([O-:13])=[O:12].[K+]>O.[OH-].[NH4+]>[O-:4][Mo:2]([O-:5])(=[O:3])=[O:1].[N+:11]([O-:14])([O-:13])=[O:12]
KomponentenVersuchsvorschriftAufarbeitungQuellen und NachweiseNotizen zur Reaktion

Komponenten

7

Edukt 3

HCID 1004Phosphoric AcidHCID 24434Potassium NitrateHCID 24621Molybdate ion

Produkt 2

HCID 943NitrateHCID 24621Molybdate ion

Reagenzien, Katalysatoren, Lösungsmittel 2

HCID 962WaterLösungsmittel2×
HCID 14923
Ammonium Hydroxide
Lösungsmittel

Versuchsvorschrift

A molybdate solution was prepared from 9.21 g of (NH4)6Mo7O24 4H2O dissolved in 50 mL of deionized water and 33 mL of concentrated ammonium hydroxide. This solution was stirred until all components were soluble. Then 12.5 g of 7G type silica gel was added to the molybdate solution and stirred to ensure homogeneity. This mixture was placed in the Microfluidizer reservoir and recirculation through the machine was started while the internal pressure was adjusted to 9,000 psi. Through Port B shown in FIG. 2 was added over 30 minutes a solution composed of 3.79 g Ni(NO3)2. 6H2O, 6.32 g, Co(NO3)2. 6H2O, 5.27 g Fe(NO3)2.b 9H2O, 2.11 g Bi(NO3)3.5H2O, 0.43 g H3PO4 (80%), and 0.04g KNO3 which had been built to a total volume of 50 mL with distilled water. The pH of the solution dropped until the final addition of the solution through Port A reached a final pH of 5. The temperature of the effluent which was recirculated through the instrument was maintained between 40°-46° C. by passing the effluent pipe through an ice water heat exchanger. The product mixture was filtered using Whatman type 1001070 filter paper affording 35.94 g. of solid product. The solid was calcined by slowly heating from 100° to 540° C. over 6 hours and held at 540° C. for 1 hour. The calcining procedure resulted in a 32% weight loss due to the decomposition of nitrate salts and the product was light brown. The X-Ray diffraction pattern of this material is illustrated in FIG. 7B. This material demonstrated 9 major reflections between 20 to 35 degree two theta at 23.3, 25.5, 26.7, 27.2, 27.5, 28.4, 28.7, 32.0, and 33.7. It was noted that reflections between 20 to 35 degree two theta at 23.3, 25.5, 26.7, 27.2, 27.5, 28.4, 28.7, 32.0, and 33.7. It was noted that this diffraction pattern appeared to contain better defined reflections and fewer separate phase metal oxides as compared to the classically prepared sample shown in FIG. 7A and described below.

Aufarbeitung

  1. stirringstirred
  2. additionwas added over 30 minutes a solution
  3. additionThe pH of the solution dropped until the final
  4. additionaddition of the solution through Port A
  5. temperaturewas maintained between 40°-46° C.
  6. temperatureheat exchanger
  7. filtrationThe product mixture was filtered
  8. filtrationfilter paper
  9. customaffording 35.94 g
  10. temperatureby slowly heating from 100° to 540° C. over 6 hours

Quellen und Nachweise

ORD-Eintrag
ord-a38bce2b8bd84f999b355e7ca76f6930
Quelldatensatz
uspto-grants-1995_11
DOI
10.6084/m9.figshare.5104873.v1
Patentnummer
US05466646

Notizen zur Reaktion

Auf dieser SeiteKomponentenVersuchsvorschriftAufarbeitungQuellen und NachweiseNotizen zur Reaktion