StartseiteMCPWorkbenchSkills
StartseiteWorkbenchBenachrichtigungenMein Bereich
llms.txt · MCP-AnleitungDatenschutz · Nutzungsbedingungen · Supportv1.8.3
  1. Startseite
  2. /Reaktion

D-Erythrose → Ribonic acid

HRID 2420624
Drucken

Reaktionsgleichung

Reaktionsgleichung von HRID 2420624
[O:1]=[C:2]([O-:11])[C@@H:3]([C@@H:5]([C@@H:7]([CH2:9][OH:10])[OH:8])[OH:6])[OH:4].[Na+].O=C([O-])[C@@H]([C@@H]([C@@H](CO)O)O)O.O=C[C@@H]([C@@H](CO)O)O.C(O)[C@@H]([C@@H](CO)O)O.[BH4-].[Na+]>O>[O:1]=[C:2]([OH:11])[C@@H:3]([C@@H:5]([C@@H:7]([CH2:9][OH:10])[OH:8])[OH:6])[OH:4]
KomponentenVersuchsvorschriftAufarbeitungQuellen und NachweiseNotizen zur Reaktion

Komponenten

7

Edukt 5

HCID 94176D-ErythroseHCID 222285Erythritol4×HCID 4311764Sodium borohydrideHCID 5460050D-RibonateHCID 56926521Sodium rel-(2R,3R,4R)-2,3,4,5-tetrahydroxypentanoate

Produkt 1

HCID 5460677Ribonic acid

Reagenzien, Katalysatoren, Lösungsmittel 1

HCID 962WaterLösungsmittel

Versuchsvorschrift

Sodium ribonate (15 mmoles) was dissolved in 20 mL of water. Cation exchange resin (Amberlite IRC747 H+ form) was added to lower the pH from 6.8 to 3.5 (or approximately 50% neutralization of the starting material). The solution was filtered to remove the cation resin, the ribonate starting material was diluted to 30 mL, and 25 mL transferred to glass cell for electrolysis. The initial ribonate solution was analyzed by HPLC against a standard and quantified to be 9.54 mmoles (0.38M). The 25 mL of starting material containing 9.54 mmoles of ribonate was stirred in the glass cell, while a constant current of 0.5 amps (100 mA/cm2) was applied. The cell voltage averaged about 6.5 volts, and the pH of the substrate increased from 3.5 to 7.6 after 2 F/mole of charge was passed. Samples were taken at 603, 1206 and 1809 coulombs. The samples containing the erythrose product were reduced to erythritol with an excess amount of sodium borohydride, and analyzed for erythritol by HPLC-RI. The samples were quantified for erythritol based on a response factor determined from an erythritol standard, see Table 1.

Aufarbeitung

  1. additionCation exchange resin (Amberlite IRC747 H+ form) was added
  2. filtrationThe solution was filtered
  3. customto remove the cation resin
  4. additionthe ribonate starting material was diluted to 30 mL, and 25 mL
  5. temperaturethe pH of the substrate increased from 3.5 to 7.6 after 2 F/mole
  6. additionof charge

Quellen und Nachweise

ORD-Eintrag
ord-d47050e2caf1402f898383baedbfdbf5
Quelldatensatz
uspto-grants-2011_06
DOI
10.6084/m9.figshare.5104873.v1
Patentnummer
US07955489B2

Notizen zur Reaktion

Auf dieser SeiteKomponentenVersuchsvorschriftAufarbeitungQuellen und NachweiseNotizen zur Reaktion