オゾン

In case of fire: keep cylinder cool by spraying water. (EPA, 1998)

In case of fire in the surroundings, use appropriate extinguishing media. Combat fire from a sheltered position.

Fresh air, rest. Half-upright position. Refer for medical attention.

ON FROSTBITE: rinse with plenty of water, do NOT remove clothes. Refer for medical attention .

First rinse with plenty of water for several minutes (remove contact lenses if easily possible), then refer for medical attention.

Warning: Effects may be delayed for 12 to 24 hours. Caution is advised.

(General first aid procedures)

CYLINDERS OF DISSOLVED OZONE SHOULD BE STORED IN REFRIGERATED AREAS & AWAY FROM ALL REDUCING AGENTS, FLAMMABLE MATERIALS & SUBSTANCES SUCH AS IRON, COPPER OR CHROMIUM THAT MAY CATALYZE DECOMP.

Store in well-ventilated, cool, dark places. Detached storage is preferred. Avoid storage near combustible materials.

Evaporation: Provide ventilation to dilute and disperse small amt of ozone into the outside atmosphere.

In the fume hood, wastes to be slowly released to air.

PROCESSES EMPLOYING OZONE SHOULD BE TOTALLY ENCLOSED OR SO EQUIPPED WITH EXHAUST VENTILATION. ... ALL ELECTRICAL EQUIPMENT SHOULD BE SUITABLY INSULATED.

SRP: The scientific literature for the use of contact lenses in industry is conflicting. The benefit or detrimental effects of wearing contact lenses depend not only upon the substance, but also on factors including the form of the substance, characteristics and duration of the exposure, the uses of other eye protection equipment, and the hygiene of the lenses. However, there may be individual substances whose irritating or corrosive properties are such that the wearing of contact lenses would be harmful to the eye. In those specific cases, contact lenses should not be worn. In any event, the usual eye protection equipment should be worn even when contact lenses are in place.

EYES: Hold eye open and rinse slowly and gently with water for 15-20 minutes. Remove contact lenses, if present, after the first 5 minutes, then continue rinsing eye. Call a poison control center or doctor for treatment advice. INHALATION: Move person to fresh air. If person is not breathing, call 911 or an ambulance, then give artificial respiration, preferably by mouth-to-mouth if possible. Call a poison control center or doctor for further treatment advice.

THYROXINE WORSENED RESPONSE TO OZONE & ANIMALS DIED FROM OTHERWISE TOLERATED DOSES. ANTITHYROID DRUGS INCR RESISTANCE TO OZONE. NERVE-BLOCKING AGENTS (PHENOXYBENZAMINE OR ERGOTAMINE) IN THE ADRENALECTOMIZED RAT ALSO INCR RESISTANCE TO OZONE.

INCR RESPIRATORY RESPONSE TO HISTAMINE INJECTED SC IN GUINEA PIGS TWO HR AFTER TWO-HR EXPOSURE TO 1 TO 5 PPM OZONE. INCR MORTALITY FROM HIGHER LEVELS OF HISTAMINE COULD BE PRODUCED BY AS LITTLE AS 0.5 TO 1 PPM OZONE. THE INCR SUSCEPTIBILITY PERSISTED UP TO 12 HR AFTER A TWO HR EXPOSURE TO 5 PPM OZONE.

ACUTE TOXICITY OF OZONE MAY BE LESSENED BY SIMULTANEOUS OR PRIOR INHALATION OR INJECTION OF ... SULFUR-CONTAINING COMPD. TECHNICAL-GRADE HYDROGEN SULFIDE GIVEN SIMULTANEOUSLY IN MOLAR RATIO OF 2:1 REDUCED MORTALITY PRODUCED BY WHAT WOULD HAVE BEEN LC50 CONCN OF OZONE TO 20%. ... MAJOR PROTECTION WAS OBTAINED BY IP INJECTION OF DIMETHYL DISULFIDE OR HYDROGEN POLYSULFIDE (ABOUT 20 MG/KG) PRIOR TO OZONE EXPOSURE.

ELEVEN HEALTHY MALE SUBJECTS AGED 23 TO 38 YR WERE EXPOSED TO PURIFIED AIR, TO NO2, O3, & SO2 ALONE, TO MIXT OF NO2 + SO2, & NO2 + O3 IN MAX ALLOWABLE CONCN, & TO A MIXT OF NO2 + SO2 + O3 IN MAX ALLOWABLE CONCN. RESPIRATORY GAS EXCHANGE FOR O2 DECR & AIRWAY RESISTANCE INCR WAS OBSERVED IN ALL SERIES WITH NO2 IN MAX ALLOWABLE CONCN. THE COMBINATIONS OF NO2 + O3, NO2 + SO2, OR NO2 + SO2 + O3 DID NOT SHOW A STRONGER EFFECT THAN NO2 ALONE.

For more Interactions (Complete) data for OZONE (20 total), please visit the HSDB record page.

At acute levels, ozone is an irritant and lachrymator. At chronically low doses (~40 nmol/mol) there is a great deal of evidence to show that ground level ozone can harm lung function and irritate the respiratory system. Long-term exposure to ozone and the pollutants that produce it is linked to premature death, asthma, bronchitis, heart attacks and other cardiopulmonary problems. Long-term exposure to ozone has been shown to increase risk of death from respiratory illness. An 18-year study on 450,000 people in the US revealed that those living in cities with high ozone levels such as Houston or Los Angeles had an over 30% increased risk of dying from lung disease. Both acute and chronic exposures to ozone can negatively impact the barrier function of the lung, and these exposures can initiate an inflammatory response from the immune system. This immune response involves the release of biologically active mediators that can have adverse effects on the lung tissue itself. Some effects may include the thickening of the air-blood barrier in the lungs, thus reducing the diffusion of oxygen into the blood. Animals exposed to ozone produce and release high amounts of a sugar known as hyaluronan. Hyaluronan has been shown to be directly responsible for causing lung airways to narrow and become irritated. (A15093)

A photochemical model was used to quantify the sensitivity of the tropospheric oxidants ozone (O3) and OH to changes in methane (CH4), carbon monoxide (CO), and NO emissions and to perturbations in climate and stratospheric chemistry. Coefficients of the form delta ln[O3]/delta ln[X] and delta ln[OH]/delta ln[X], where [X]= flux of CH4, CO, NO, stratospheric O3, and H2O have been calculated for a number of chemically coherent regions (e.g. nonpolluted continental, nonpolluted marine, urban) at low and middle latitudes. Sensitivities in O3 and OH vary with regional emissions patterns and are nonlinear within a given region as [X] changes. In most cases incr CH4 an CO emissions will suppress OH (neg coefficients) in incr O3 (pos coefficients) except in areas where NO and O3 influenced by pollution are sufficient to incr OH. Stratospheric O3 depletion will tend to decr O3 (except in high NOx areas) and incr OH through enhanced UV photolysis. Incr levels of water vapor (one possible outcome of a global warming) will also decr O3 and incr OH. In most regions, NO, CO and CH4 emission incr will suppress OH and incr O3, but these trends may be opposed by stratospheric O3 depletion and climate change. A regional survey of OH and O3 levels suggests that the tropics have a pivotal role in determining the earth's future oxidizing capacity.

Ozone concn above 80 ppb are common in the East U.S. in spring and summer, but they are unusual in the West, and ozone shows considerably more day-to-day variability in the East. Variations in ozone levels are highly correlated over distances of several hundred kilometers in the East, indicating that high values are associated with episodes of large spatial scale, > 600,000 sq km. There were 10 and 7 such episodes in 1978 and 1979, respectively, between the mo of Apr and Sept; they persisted for 3-4 days, on avg, with a range of 2-8 days, and were most common in Jun. Daily max ozone values exceeded 90 ppb at over half the sites during these episodes and were often > 120 ppb at one or more sites. An analysis of the meteorology for each episode shows that they occurred preferentially in the presence of weak, slow-moving, and persistent high-pressure systems. Two episodes that occurred outside the summer half of the yr were associated with unseasonably warm weather; only 1 episode, in Mar 1978, appeared to reflect a major stratospheric intrusion. Concn of NOx at rural locations in the East are frequently high enough (> 1 ppb) to permit significant photochemical formation of ozone. It is clear that rural ozone in the East in spring and summer is severely impacted by anthropogenic emissions of NOx and hydrocarbons, and that ozone episodes occur when the weather is particularly conducive to photochemical formation of ozone. Ozone episodes were present on 23% of days in May-Aug in the East in 1978-1979.

Measurements from the eastern north Pacific stratocumulus regime have been used to study components of the regional ozone budget. The surface destruction rate was determined by eddy correlation of ozone and vertical velocity measured during 8 flights of a low flying aircraft. Significant variability (2580 to 6460 s/m) was found in the measured surface resistance; it was partially correlated with friction velocity but appears to have other controlling influences as well. The mean resistance was 4190 + or - 840 s/m, which is higher (slower destruction) than most previous estimates for seawater. Flux and mean measurements throughout the marine boundary layer were used to estimate the net rate of in-situ photochemical production/destruction of ozone. Averaged over the flights, ozone concn was found to be near steady state, and a net photochemical destruction of 0.02 to 0.07 ng/cu m/sec was diagnosed. Ozone vertical distributions above the boundary layer showed a strongly layered structure with very sharp gradients.

The substance can be absorbed into the body by inhalation.

inhalation, skin and/or eye contact

Inhalation

Ozone is a strong oxidant and reacts directly with organic double bonds. When ozone breaks down to dioxygen it gives rise to oxygen free radicals, which are highly reactive and capable of damaging many organic molecules. Moreover, it is believed that the powerful oxidizing properties of ozone may be a contributing factor of inflammation. When inhaled, ozone reacts with compounds lining the lungs to form specific, cholesterol-derived metabolites that are thought to facilitate the build-up and pathogenesis of atherosclerotic plaques. These metabolites have been confirmed as naturally occurring in human atherosclerotic arteries and are categorized into a class of secosterols termed atheronals, generated by ozonolysis of cholesterol's double bond to form a 5,6 secosterol. Ozone has also been shown to form the suspected carcinogen bromate when it is introduced to source water with high bromide concentrations. Studies have also demonstrated an increase in collagen, a structural protein involved in fibrosis, following prolonged ozone exposure. Acute and short-term exposure studies have demonstrated ozone’s effects on lung lipids which include an increase in arachidonic acid (a pro-inflammatory molecule).

Sore throat. Cough. Headache. Shortness of breath. Laboured breathing.

ON CONTACT WITH LIQUID: FROSTBITE.

Redness. Pain.

irritation eyes, mucous membrane; pulmonary edema; chronic resp disease

Exposure of 0.1 to 1 μmol/mol produces headaches, burning eyes and irritation to the respiratory passages. Exposure to 10 ppm ozone will cause pulmonary edema. Low doses act as a depressant and will induce sleep in certain individuals.

The following link will take the user to the National Toxicology Program (NTP) Test Agent Search Results page, which tabulates all of the "Standard Toxicology & Carcinogenesis Studies", "Developmental Studies", and "Genetic Toxicity Studies" performed with this chemical. Clicking on the "Testing Status" link will take the user to the status (i.e., in review, in progress, in preparation, on test, completed, etc.) and results of all the studies that the NTP has done on this chemical. [http://ntp-apps.niehs.nih.gov/ntp_tox/index.cfm?fuseaction=ntpsearch.searchresults&searchterm=10028-15-6]

FORMED LOCALLY IN AIR FROM LIGHTNING, IN STRATOSPHERE BY UV RADIATION

FOUND IN ATMOSPHERE IN VARYING PROPORTIONS (ABOUT 0.05 PPM @ SEA LEVEL), SINCE IT IS PRODUCED CONTINUOUSLY INTHE OUTER LAYERS OF THE ATMOSPHERE BY THE ACTION OF SOLAR UV RADIATION ON THE OXYGEN OF THE AIR.

Releases of CERCLA hazardous substances are subject to the release reporting requirement of CERCLA section 103, codified at 40 CFR part 302, in addition to the requirements of 40 CFR part 355. Ozone is an extremely hazardous substance (EHS) subject to reporting requirements when stored in amounts in excess of its threshold planning quantity (TPQ) of 100 lbs.

Occupational exposure from welding fumes; Also used as a disinfectant in water treatment and as a bleaching agent in food, textile, and paper processing; [Levy, p. 409] . . . Gas metal arc and gas tungsten arc welding produce the highest ozone concentrations, especially when aluminum is used as a base metal. [Welding, Brazing and Thermal Cutting. NIOSH Criteria for a Recommended Standard. Publication No. 88-110:33,1988] TWA ozone concentrations exceeded the ACGIH TLV at a pulp and paper plant construction site. The source was the electrostatic precipitators on the operating boiler stacks located upwind from the construction site. [Appl Occup Environ Hyg. 1999 Apr;14(4):203-7]

Welding [Category: Weld]

Ceramics making [Category: Hobbies]

AS DISINFECTANT FOR AIR AND WATER BY VIRTUE OF ITS OXIDIZING POWER. FOR BLEACHING WAXES, TEXTILES, OILS. IN ORGANIC SYNTHESES.

OZONOLYSIS OF UNSATURATED FATTY ACIDS TO PELARGONIC ACID, AZELAIC ACID & TO OTHER ACIDS; OXIDATION OF FURNACE CARBON BLACK FOR INK BLACK MFR; CATALYST IN PRODN OF PEROXYACETIC ACID; WATER TREATMENT FOR TASTE & ODOR CONTROL; MOLD & BACTERIA INHIBITOR IN COLD STORAGE.

Used as an oxidizing agent in the organic chemical industry (eg, production of azelaic acid); as a disinfectant for food in cold storage rooms; ... for bleaching ... flour, paper pulp, starch, and sugar; for aging liquor and wood; for processing certain perfumes, vanillin, and camphor; in treating industrial wastes; in the rapid drying of varnishes and printing inks; and in the deodorizing of feathers.

IN THE LAB OZONE IS PREPD BY PASSING DRY AIR BETWEEN TWO PLATE ELECTRODES CONNECTED TO AN ALTERNATING CURRENT SOURCE OF SEVERAL THOUSAND VOLTS. THE REACTION IS REVERSIBLE, & AFTER A LITTLE OZONE HAS BEEN PRODUCED IT IS DECR AT THE SAME RATE AS IT IS GENERATED. OBTAINED IN PURE FORM BY COOLING OZONIZED AIR TO -180 °C WHEN IT SEPARATES AS A DARK BLUE LIQ.

COMMERCIAL MIXT CONTAINING UP TO 2% OZONE ARE PRODUCED BY ELECTRONIC IRRADIATION OF AIR. IT IS USUALLY MFR ON THE SPOT, AS IT IS TOO EXPENSIVE TO SHIP. TONNAGE QUANTITIES ARE USED.

Ozone is prepared by the heating of silver difluoride in a dilute aqueous acid

Other (requires additional information)

Ozone: ACTIVE

DETERIORATION OF RUBBER IS ACCELERATED BY TRACES OF OZONE.

OZONE IS A HIGHLY EFFICIENT DISINFECTANT WHICH MAY HAVE SIGNIFICANT ADVANTAGES IN WATER TREATMENT COMPARED TO CHLORINE. IT HAS, HOWEVER, BEEN SHOWN THAT MUTAGENIC & POSSIBLY CARCINOGENIC BY-PRODUCTS MAY BE PRODUCED UNDER CERTAIN CONDITIONS OF OZONATION. LIGHT CHLORINATION FOLLOWING OZONIZATION MAY MEET THE HIGHEST STANDARDS OF WATER DISINFECTION. IN MANY CASES OZONE TREATMENT ALONE MAY SUFFICE.

Contributes to formation of photochemical smog.

The ozone generation rate and particle size dependent (0.01-10 micrometers) filtration efficiency of an in-duct residential electronic air cleaner were measured. Filtration efficiencies were typically 70-90%, showing decreasing efficiency with increasing flowrate. Ozone generation rates were about 3 ug/s. Scans of the aerosol concn on the downwind face of the electronic air cleaner were used to locate, then eliminate, areas of aerosol sneakage. Sneakage was detected along the top and bottom of the electronic air cleaner face, apparently due to incomplete aerosol charging for aerosol passing near the ends of the ionizing wires. Areas away from the top and bottom had near-zero aerosol penetration. Based on these results, the inlet to the electronic air cleaner was masked to eliminate airflow through the sneakage areas. The resultant efficiency of the masked electronic air cleaner was nearly 100% for particles larger than 0.1 micrometer diameter; however, the filtration efficiency for particles smaller than 0.1 um was not significantly affected by masking.