ホームMCPワークベンチSkills
ホームワークベンチ通知マイページ
llms.txt · MCPガイドプライバシーポリシー · 利用規約 · サポートv1.8.3
  1. ホーム
  2. /反応

Tetrabutylammonium → Methacrylic Acid

HRID 1588122
印刷

反応式

HRID 1588122 の反応式
C[O:2][C:3]([O:7][Si](C)(C)C)=[C:4]([CH3:6])[CH3:5].C([N+](CC[CH2:27][CH3:28])(CCCC)CCCC)CCC.[C:29]([O:34][Si](C)(C)C)(=[O:33])[C:30]([CH3:32])=[CH2:31].C(OCCC1C=CC=CC=1)(=[O:43])C(C)=C.C(O)(=O)C(C)=C.[CH2:59]([O:61][CH:62]([OH:71])[CH2:63][O:64][CH2:65][CH2:66][O:67]CCO)[CH3:60].O.O.O.[F-].C([N+](CCCC)(CCCC)CCCC)CCC>C1(=O)OC(C)CO1.C1COCC1.CO>[C:3]([OH:7])(=[O:2])[C:4]([CH3:6])=[CH2:5].[C:29]([OH:34])(=[O:33])[C:30]([CH3:32])=[CH2:31].[CH3:60][CH2:59][O:61][CH:62]([OH:71])[CH2:63][O:64][CH2:65][CH2:66][O:67][CH2:27][CH2:28][OH:43]
参加物反応条件実験手順後処理出典と根拠反応ノート

参加物

11

反応物 6

HCID 16028Tetrabutylammonium3 回HCID 772602-Phenylethyl methacrylateHCID 552336Silane, ((1-methoxy-2-methyl-1-propenyl)oxy)trimethyl-HCID 27338392-Propenoic acid, 2-methyl-, trimethylsilyl ester2 回HCID 11726816Tetrabutylammonium Fluoride TrihydrateHCID 86746980b-Ethoxytriethylene glycol methacrylate
2 回

生成物 2

HCID 4093Methacrylic AcidHCID 86746980b-Ethoxytriethylene glycol methacrylate

試薬・触媒・溶媒 3

HCID 887Methanol溶媒HCID 7924Propylene Carbonate溶媒3 回HCID 8028Tetrahydrofuran溶媒

反応条件

温度
30 °C

実験手順

To a solution of 22.6 g (26.2 mL, 130 mmol) of 1-methoxy-1-trimethylsiloxy-2-methyl-1-propene and 0.1 mL of tetrabutylammonium biacetate (0.1 M in propylene carbonate) in 300 mL of THF was added dropwise 268 g (304 mL, 1.69 mole) of trimethylsilyl methacrylate. During the course of the addition the temperature of the reaction mixture rose slowly to 50° C. To increase the rate of polymerization, an additional 1.5 mL of tetrabutylammonium biacetate (0.1 M in propylene carbonate) was added in 7 portions. After all of the monomer had been added, the temperature began to fall, and the solution was cooled with a bath to 30° C. The addition of 248 g (245 mL, 1.3 mole) of 2-phenylethyl methacrylate (purified by passage over a column of basic alumina under argon) was begun. An additional 0.6 mL of tetrabutylammonium biacetate (0.1 M in propylene carbonate) was added. During the addition the temperature rose 48° C. When the addition was complete and the temperature began to fall, the solution was cooled to 31° C., 0.15 mL of tetrabutylammonium biacetate (0.1 M in propylene carbonate) was added, and 128 g (128 mL, 0.52 mole) of ethoxytriethylene glycol methacrylate (purified by passage over a column of basic alumina under argon) was added dropwise from an addition funnel. Since little temperature change was observed, an additional 0.15 mL of tetrabutylammonium biacetate (0.1 M in propylene carbonate) was added to insure completion of the polymerization. Analysis of an aliquot of the solution by 1H nmr showed that there was no residual monomer present. To the solution of poly(trimethylsilyl methacrylate [48 mol %]-b-2-phenylethyl methacrylate [37 mol %]-b-ethoxytriethylene glycol methacrylate [15 mol %]) was added 350 mL of 0.03 M tetrabutylammonium fluoride trihydrate in methanol. The resulting mixture was refluxed for 16 hr and evaporated in a rotary evaporator under reduced pressure. The residual polymer was dried for 48 hr in a vacuum oven to give 515 g of poly(methacrylic acid [48 mol %]-b-2-phenylethyl methacrylate [37 mol %]-b-ethoxytriethylene glycol methacrylate [15 mol %]). 1NMR analysis of the product showed that no trimethylsilyl ester groups remained.

後処理

  1. additionDuring the course of the addition the temperature of the reaction mixture
  2. customrose slowly to 50° C
  3. temperatureTo increase
  4. customthe rate of polymerization
  5. additionAfter all of the monomer had been added
  6. custompurified by passage over a column of basic alumina under argon)
  7. additionAn additional 0.6 mL of tetrabutylammonium biacetate (0.1 M in propylene carbonate) was added
  8. additionDuring the addition the temperature
  9. customrose 48° C
  10. additionWhen the addition
  11. temperaturethe solution was cooled to 31° C.
  12. addition0.15 mL of tetrabutylammonium biacetate (0.1 M in propylene carbonate) was added
  13. additionwas added dropwise from an addition funnel
  14. customcompletion of the polymerization
  15. temperatureThe resulting mixture was refluxed for 16 hr
  16. customevaporated in a rotary evaporator under reduced pressure
  17. customThe residual polymer was dried for 48 hr in a vacuum oven

出典と根拠

ORDレコード
ord-b5400a2134324a16b4a94336163b0aac
出典データセット
uspto-grants-1993_06
DOI
10.6084/m9.figshare.5104873.v1
特許番号
US05219945

反応ノート

このページの内容参加物反応条件実験手順後処理出典と根拠反応ノート