ホームMCPワークベンチSkills
ホームワークベンチ通知マイページ
llms.txt · MCPガイドプライバシーポリシー · 利用規約 · サポートv1.8.3
  1. ホーム
  2. /反応

Ethylene Glycol → Ethylene 4,4'-biphenyldicarboxylate

HRID 846828
印刷

反応式

HRID 846828 の反応式
[C:1]1([C:11]2[CH:16]=[CH:15][C:14]([C:17]([O:19][CH3:20])=[O:18])=[CH:13][CH:12]=2)[CH:6]=[CH:5][C:4]([C:7]([O:9][CH3:10])=[O:8])=[CH:3][CH:2]=1.C1(C2C=CC(C(OC)=O)=CC=2)C=CC=C(C(OC)=O)C=1.C(O)CO>CC(C)[O-].CC(C)[O-].CC(C)[O-].CC(C)[O-].[Ti+4]>[C:11]12[C:1]3[CH:6]=[CH:5][C:4](=[CH:3][CH:2]=3)[C:7](=[O:8])[O:9][CH2:10][CH2:20][O:19][C:17](=[O:18])[C:14]([CH:15]=[CH:16]1)=[CH:13][CH:12]=2
参加物反応条件実験手順後処理出典と根拠反応ノート

参加物

5

反応物 3

HCID 174Ethylene GlycolHCID 13099Dimethyl 4,4'-biphenyldicarboxylateHCID 108747(1,1'-Biphenyl)-3,4'-dicarboxylic acid, 3,4'-dimethyl ester

生成物 1

HCID 67910781Ethylene 4,4'-biphenyldicarboxylate

試薬・触媒・溶媒 1

HCID 11026Titanium isopropoxide触媒

反応条件

温度
260 °C

実験手順

A clear solution of 243.3 g (0.900 mole) of dimethyl 4,4'-biphenyldicarboxylate, 81.2 g of dimethyl 3,4'-biphenyldicarboxylate, 150.5 g (2.43 mole) of ethylene glycol and 50 μL of titanium tetraisopropoxide is stirred at 217° C. under nitrogen in a 1-L round bottom flask equipped with a paddle stirrer, Vigreaux column, distillation head, condenser, receiver and nitrogen inlet. The apparatus is heated in a molten salt bath until methanol begins to distill. After 2.7 hours, the temperature is slowly increased to 260° C. where it is held for 45 minutes. The distillate (104 mL) that has collected is discarded. Over the next 48 minutes the temperature is increased to 300° C. and the pressure is slowly reduced to 1 mm Hg. More liquid is distilled. The viscosity of the clear reaction mass slowly increases. After 8 minutes at 300° C., the heating bath is lowered and nitrogen is admitted. The polymer solidifies to an opaque creamy white solid when it cools. It is ground to coarse granules in a Wiley mill. The copolyester has an inherent viscosity of 0.72 dL/g, a Tg of 122° C. and a Tm of 293° C. The molecular weight of this polymer is advanced in the solid state by stirring the granules at 240° C. and 1 mm Hg for 3.2 hours. The advanced polymer has an inherent viscosity of 1.05 dL/g. It is injection molded into standard one eight-inch thick test bars at 316° C. into a mold held at 65° C. using an Arburg 170CDM injection molding machine. The tensile modulus and impact strength of these test bars are measured using procedures described in ASTM Test Nos. D638 and D256, respectively. The tensile modulus is 578 kpsi and the notched Izod impact strength is 1.2 ft. lb./in.

後処理

  1. customequipped with a paddle stirrer
  2. distillationVigreaux column, distillation head, condenser, receiver and nitrogen inlet
  3. temperatureThe apparatus is heated in a molten salt bath until methanol
  4. distillationto distill
  5. waitis held for 45 minutes
  6. distillationThe distillate (104 mL) that has collected
  7. temperatureOver the next 48 minutes the temperature is increased to 300° C.
  8. distillationMore liquid is distilled
  9. temperatureThe viscosity of the clear reaction mass slowly increases
  10. waitAfter 8 minutes at 300° C.
  11. customa Tm of 293° C
  12. wait1 mm Hg for 3.2 hours
  13. custommolded into standard one eight-inch thick test bars at 316° C. into a mold
  14. customheld at 65° C.

出典と根拠

ORDレコード
ord-b12b9b51348f4fafadf247cbce024451
出典データセット
uspto-grants-1992_08
DOI
10.6084/m9.figshare.5104873.v1
特許番号
US05138022

反応ノート

このページの内容参加物反応条件実験手順後処理出典と根拠反応ノート