홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.1
  1. 홈
  2. /반응

Vinylidene fluoride → Pmve tfe

HRID 1160490
인쇄

반응식

HRID 1160490 반응식
S(OOS([O-])(=O)=O)([O-])(=O)=O.[NH4+].[NH4+].[OH-].[Na+].C(F)(F)=C.[C:19]([F:28])([O:23][C:24]([F:27])([F:26])[F:25])=[C:20]([F:22])[F:21].[F:29][C:30]([F:34])=[C:31]([F:33])[F:32].BrC(F)(F)C(F)(F)C=C>>[C:19]([F:28])([O:23][C:24]([F:27])([F:26])[F:25])=[C:20]([F:22])[F:21].[F:29][C:30]([F:34])=[C:31]([F:33])[F:32]
참가 물질실험 절차후처리출처 및 근거반응 노트

참가 물질

7

반응물 6

HCID 6369Vinylidene fluorideHCID 8301TetrafluoroethyleneHCID 14474Perfluoro(methyl vinyl ether)HCID 14798Sodium HydroxideHCID 62648Ammonium PersulfateHCID 877214-Bromo-3,3,4,4-tetrafluoro-1-butene

생성물 1

HCID 44148445
Pmve tfe

실험 절차

A VF2/PMVE/TFE copolymer fluoroelastomer was prepared by a continuous emulsion polymerization process, carried out at 105° C. in a well-stirred 2.0-liter stainless steel liquid full reaction vessel. An aqueous solution, consisting of 1.98 g/hour (g/h) ammonium persulfate initiator and 0.79 g/h sodium hydroxide, was fed to the reactor at a rate of 4 L/hour. The reactor was maintained at a liquid-full level at a pressure of 6.2 MPa by means of a backpressure control valve in the effluent line. After 30 minutes, polymerization was initiated by introduction of a gaseous monomer mixture consisting of 569 g/h vinylidene fluoride (VF2), 393 g/h perfluoro(methyl vinyl ether) (PMVE), and 101 g/h tetrafluoroethylene (TFE), fed through a diaphragm compressor. Fifteen minutes after polymerization commenced, 4-bromo-3,3,4,4-tetrafluoro-1-butene (BTFB) was fed into the reactor at a rate of 10.0 g/h. After a further 1.75 hours, collection of effluent dispersion was begun and collection continued for 5 hours. The effluent polymer latex, which had a pH of 8.64 and contained 20.7 wt. % solids, was separated from residual monomers in a degassing vessel at atmospheric pressure.

후처리

  1. customcarried out at 105° C. in a well-stirred 2.0-liter stainless steel liquid full reaction vessel
  2. temperatureThe reactor was maintained at a liquid-full level at a pressure of 6.2 MPa by means of a backpressure control valve in the effluent line
  3. custompolymerization
  4. customFifteen minutes after polymerization
  5. waitAfter a further 1.75 hours
  6. customcollection of effluent dispersion
  7. customcollection
  8. waitcontinued for 5 hours
  9. customwas separated from residual monomers in a degassing vessel at atmospheric pressure

출처 및 근거

ORD 기록
ord-1d9305d84c894b28ab4aa7bd3bc24d07
출처 데이터셋
uspto-grants-2010_10
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US07816468B2

반응 노트

이 페이지에서참가 물질실험 절차후처리출처 및 근거반응 노트