홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Iodine → 2-Fluoro-3-iodo-4-methylbenzonitrile

HRID 1668927
인쇄

반응식

HRID 1668927 반응식
CC1(C)CCCC(C)(C)N1.C([Li])CCC.[F:16][C:17]1[CH:24]=[C:23]([CH3:25])[CH:22]=[CH:21][C:18]=1[C:19]#[N:20].[I:26]I.[O-]S([O-])(=S)=O.[Na+].[Na+]>C1COCC1>[F:16][C:17]1[C:24]([I:26])=[C:23]([CH3:25])[CH:22]=[CH:21][C:18]=1[C:19]#[N:20]
참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트

참가 물질

7

반응물 5

HCID 807IodineHCID 130352,2,6,6-TetramethylpiperidineHCID 24477Sodium ThiosulfateHCID 27784432-Fluoro-4-methylbenzonitrileHCID 178418339Butyllithium

생성물 1

HCID 593838982-Fluoro-3-iodo-4-methylbenzonitrile수율 48%

시약·촉매·용매 1

HCID 8028Tetrahydrofuran용매3회

반응 조건

온도
-50 °C

실험 절차

A solution of 2,2,6,6,-tetramethylpiperidine (45 mL, 267 mmol) in THF (400 mL) was cooled below −80° C. under N2-atmosphere. n-Butyl lithium (2.5M in hexane, 110 mL, 275 mmol) was added slowly maintaining the temperature of the mixture below −70° C. After complete addition, the reaction mixture was warmed to −50° C. and stirred at this temperature for 30 minutes. The clear solution became turbid indicating the salt formation. It was cooled to −80° C. again and a solution of 2-fluoro-4-methylbenzonitrile (32.4 g, 240 mmol) in THF (150 mL) was slowly added taking care that the temperature of the reaction mixture remained below −70° C. It was then warmed up to −50° C. and stirred for 30 minutes. The mixture was then cooled to −70° C. and a saturated solution of I2 (67 g, 264 mmol) in THF was added slowly maintaining the temperature at −70° C. After complete addition, the mixture was warmed to ambient temperature. It was added to a solution of Na2S2O3 (160 g in 1.5 L of water) and stirred for an hour. The organic part was separated and the aqueous layer was extracted with EtOAc. The organic layers were combined and washed with brine. The organic layer was then dried over Na2SO4 and filtered. The volatiles were evaporated under reduced pressure. The crude product was subjected to vacuum distillation; at about 60° C., excess TMP was removed, at about 100° C., the starting compound 2-fluoro-4-methylbenzonitrile and a small amount of product was removed and, finally at 115° C., pure 2-fluoro-3-iodo-4-methylbenzonitrile was obtained (30 g, 48% yield). MS (M+H)+ 262.

후처리

  1. temperaturemaintaining the temperature of the mixture below −70° C
  2. additionAfter complete addition
  3. temperatureIt was cooled to −80° C. again
  4. customremained below −70° C
  5. temperatureIt was then warmed up to −50° C.
  6. stirringstirred for 30 minutes
  7. temperatureThe mixture was then cooled to −70° C.
  8. temperaturemaintaining the temperature at −70° C
  9. additionAfter complete addition
  10. temperaturethe mixture was warmed to ambient temperature
  11. stirringstirred for an hour
  12. customThe organic part was separated
  13. extractionthe aqueous layer was extracted with EtOAc
  14. washwashed with brine
  15. dry with materialThe organic layer was then dried over Na2SO4
  16. filtrationfiltered
  17. customThe volatiles were evaporated under reduced pressure
  18. distillationThe crude product was subjected to vacuum distillation
  19. customat about 60° C., excess TMP was removed, at about 100° C.
  20. customthe starting compound 2-fluoro-4-methylbenzonitrile and a small amount of product was removed and, finally at 115° C.

출처 및 근거

ORD 기록
ord-77027c4a8c584ec2a2902a1389851475
출처 데이터셋
uspto-grants-2011_08
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US07989461B2

반응 노트

이 페이지에서참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트