홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Isobutyric Acid → 2,2-Dimethyl-3-(thiophen-2-yl)propanoic acid

HRID 2059084
인쇄

반응식

HRID 2059084 반응식
[H-].[Na+].C(NC(C)C)(C)C.[C:10]([OH:15])(=[O:14])[CH:11]([CH3:13])[CH3:12].C([Li])CCC.CCCCCC.Cl[CH2:28][C:29]1[S:30][CH:31]=[CH:32][CH:33]=1>O.C1COCC1>[CH3:12][C:11]([CH3:13])([CH2:28][C:29]1[S:30][CH:31]=[CH:32][CH:33]=1)[C:10]([OH:15])=[O:14]
참가 물질실험 절차후처리출처 및 근거반응 노트

참가 물질

9

반응물 6

HCID 6590Isobutyric AcidHCID 7912DiisopropylamineHCID 8058HexaneHCID 24758Sodium hydrideHCID 698302-(Chloromethyl)thiopheneHCID 178418339Butyllithium

생성물 1

HCID 104877462,2-Dimethyl-3-(thiophen-2-yl)propanoic acid

시약·촉매·용매 2

HCID 962Water용매HCID 8028Tetrahydrofuran용매

실험 절차

A mixture of 57% oil emulsion of sodium hydride (3.14 g., 0.074 mole), THF (68 ml.) and diisopropylamine (6.87 g., 0.068 mole) was placed under N2. Isobutyric acid (5.98 g., 0.068 mole) was added dropwise. The mixture was heated at reflux for 15 min. to complete formation of the salt. After cooling at 0°, a solution of 1.6 molar n-butyllithium in hexane (42 ml., 0.068 mole) was added in small portions while holding the temperature below 10°. The resulting turbid solution was kept at 0° for 15 min. and then warmed to 30°-35° for 30 min. After again cooling to 0°, 2-chloromethylthiophene (9 g., 0.068 mole) was added dropwise over 15-20 min. while holding temperature between 0° and 5°. The mixture was kept at 0° for 30 min., in the range of 30°-35° for 1 hr. and was then cooled to 15°. Water (90 ml.) was added dropwise and the aqueous layer was separated. The organic phase was washed with a mixture of water (50 ml.) and Et2O (75 ml.). The aqueous extracts were combined, washed with Et2O and then acidified with conc. HCl. The oily product was extracted with Et2O and the combined ET2O extracts were dried over MgSO4. Evaporation of the Et2O in vacuo gave 11.4 g. (91%) of product of sufficient purity to be used for conversion into (IVa). The NMR spectrum is consistent with the assigned structure.

후처리

  1. temperatureThe mixture was heated
  2. temperatureat reflux for 15 min.
  3. temperatureAfter cooling at 0°
  4. customthe temperature below 10°
  5. temperaturewarmed to 30°-35° for 30 min
  6. temperatureAfter again cooling to 0°
  7. customtemperature between 0° and 5°
  8. waitThe mixture was kept at 0° for 30 min., in the range of 30°-35° for 1 hr
  9. temperatureand was then cooled to 15°
  10. customthe aqueous layer was separated
  11. washThe organic phase was washed with a mixture of water (50 ml.) and Et2O (75 ml.)
  12. washwashed with Et2O
  13. extractionThe oily product was extracted with Et2O
  14. dry with materialthe combined ET2O extracts were dried over MgSO4
  15. customEvaporation of the Et2O in vacuo
  16. customgave 11.4 g

출처 및 근거

ORD 기록
ord-ba164daebb2443fbbe1161e566cc81a6
출처 데이터셋
uspto-grants-1982_03
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US04321398

반응 노트

이 페이지에서참가 물질실험 절차후처리출처 및 근거반응 노트