홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Tetrahydrofuran → 3,5-Bis(trifluoromethyl)benzamide

HRID 2268203
인쇄

반응식

HRID 2268203 반응식
[F:1][C:2]([F:15])([F:14])[C:3]1[CH:4]=[C:5](Br)[CH:6]=[C:7]([C:9]([F:12])([F:11])[F:10])[CH:8]=1.[O:16]1[CH2:20]CCC1.O.[NH3:22].[C]=O>C([O-])(=O)C.[Pd+2].C([O-])(=O)C.C1(P(C2C=CC=CC=2)C2C=CC=CC=2)C=CC=CC=1.O>[F:1][C:2]([F:15])([F:14])[C:3]1[CH:4]=[C:5]([CH:6]=[C:7]([C:9]([F:12])([F:11])[F:10])[CH:8]=1)[C:20]([NH2:22])=[O:16]
참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트

참가 물질

8

반응물 4

HCID 8028TetrahydrofuranHCID 676021-Bromo-3,5-bis(trifluoromethyl)benzeneHCID 12896473Azane;hydrateHCID 178418416HCID 178418416, 화합물2회

생성물 1

HCID 5199273,5-Bis(trifluoromethyl)benzamide

시약·촉매·용매 3

HCID 11776Triphenylphosphine
촉매
HCID 167845palladium(II) acetate촉매
HCID 962Water용매

반응 조건

온도
82.5 °C

실험 절차

A 1000-ml autoclave made of stainless steel was charged with 400 g of 3,5-bis(trifluoromethy)bromobenzene, 227 ml of tetrahydrofuran, 1.53 g of palladium acetate, 5.37 g of triphenylphosphine, and 371 g of 25% ammonia water. Stirring for the content of the autoclave was started, upon which nitrogen gas displacement for the autoclave was made. Thereafter, the initial pressure of carbon monoxide gas was set at 3 kg/cm2, and then heating for the autoclave was started. After lapse of 1 hour, the inside temperature of the autoclave reached 100° C., at which the inside pressure of the autoclave was adjusted at 10 kg/cm2 upon introduction of carbon monoxide under pressure. During reaction, the inside temperature and pressure were respectively kept at 100° C. and 10 kg/cm2. After lapse of 11 hours, the autoclave was cooled, and the gas inside the autoclave was purged. A reaction mixture or liquid was taken out into a separatory funnel, in which the reaction liquid was separated into two layers. One (organic layer) of the two layers was sampled. A separately prepared 2000-ml flask provided with a stirrer was charged with 700 ml of water and heated at 80 to 85° C. in an oil bath. At this time, the above sampled organic layer was added dropwise into the flask. When distillation of tetrahydrofuran had been completed, heating for the flask was stopped so as to cool the content of the flask to room temperature. Crystals formed in the cooled flask was subjected to a suction filtration, and thereafter rinsed with 900 ml of cool water and then rinsed with 250 ml of toluene two times to obtain a toluene-rinsed solution. As a result, 241.3 g of 3,5-bis(trifluoromethyl)benzamide was obtained. 3,5-bis(trifluoromethyl)benzamide had a melting point ranging from 160 to 162° C.

후처리

  1. temperatureheating for the autoclave
  2. customAfter lapse of 1 hour
  3. customreached 100° C., at which
  4. customDuring reaction
  5. customwere respectively kept at 100° C.
  6. temperatureAfter lapse of 11 hours, the autoclave was cooled
  7. customthe gas inside the autoclave was purged
  8. customA reaction mixture or liquid was taken out into a separatory funnel, in which
  9. customthe reaction liquid
  10. customwas separated into two layers
  11. aliquotOne (organic layer) of the two layers was sampled
  12. customA separately prepared 2000-ml flask provided with a stirrer
  13. additionAt this time, the above sampled organic layer was added dropwise into the flask
  14. distillationWhen distillation of tetrahydrofuran
  15. temperatureheating for the flask
  16. temperatureto cool the content of the flask to room temperature
  17. customCrystals formed in the cooled flask
  18. filtrationwas subjected to a suction filtration
  19. washrinsed with 900 ml of cool water
  20. washrinsed with 250 ml of toluene two times
  21. customto obtain a toluene-
  22. washrinsed solution

출처 및 근거

ORD 기록
ord-785d4372205a46aebb2f8f8b7a7f6913
출처 데이터셋
uspto-grants-2001_12
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US06326517B1

반응 노트

이 페이지에서참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트