홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Diisopropylamine → 2,2-Dimethyl-5-[2-(4-pyridinyl)ethenyl]-3(2H)-furanone

HRID 359372
인쇄

반응식

HRID 359372 반응식
C(NC(C)C)(C)C.C([Li])CCC.[CH3:13][C:14]1([CH3:21])[C:18](=[O:19])[CH:17]=[C:16]([CH3:20])[O:15]1.[N:22]1[CH:27]=[CH:26][C:25]([CH:28]=O)=[CH:24][CH:23]=1.FC(F)(F)C(OC(=O)C(F)(F)F)=O>O1CCCC1.CCCCCC.C(N(CC)CC)C.CN(C)P(N(C)C)(N(C)C)=O>[CH3:13][C:14]1([CH3:21])[C:18](=[O:19])[CH:17]=[C:16]([CH:20]=[CH:28][C:25]2[CH:26]=[CH:27][N:22]=[CH:23][CH:24]=2)[O:15]1
참가 물질실험 절차후처리출처 및 근거반응 노트

참가 물질

10

반응물 5

HCID 7912DiisopropylamineHCID 9845Trifluoroacetic anhydrideHCID 133894-PyridinecarboxaldehydeHCID 1370803(2H)-Furanone, 2,2,5-trimethyl-HCID 178418339Butyllithium

생성물 1

HCID 543140152,2-Dimethyl-5-[2-(4-pyridinyl)ethenyl]-3(2H)-furanone수율 32%

시약·촉매·용매 4

HCID 8028Tetrahydrofuran용매3회HCID 8058Hexane용매HCID 8471Triethylamine용매HCID 12679Hexamethylphosphoramide용매

실험 절차

To a solution of dry diisopropylamine (2.6 mL, 19.1 mM) in dry tetrahydrofuran (350 mL) at -78° C., was added dropwise a 2.5M solution of n-butyllithium in hexane (7.6 mL, 19.1 mM). After the reaction solution was stirred for 15 minutes, a solution of 2,2,5-trimethyl-3(2H)-furanone (20 g, 15.9 mM) in tetrahydrofuran (25 mL) was added dropwise. Hexamethylphosphoramide (6.4 mL, 35.7 mM) was then added after 30 minutes. Finally, 4-pyridinecarboxaldehyde (2.5 g, 23.5 mM) in tetrahydrofuran (25 mL) was added in one portion. The reaction solution was stirred 15 minutes when trifluoroacetic anhydride (6.7 mL, 47.7 mM) was added in one portion. Again, the reaction solution was stirred 15 minutes before triethylamine (11 mL, 80 mM) was added and was allowed to warm to room temperature. The reaction mixture was concentrated to 100 mL then diluted with diethyl ether (300 mL). The organic layer was extracted with 1N aqueous hydrochloric acid (100 mL). The acid layer was neutralized with solid sodium bicarbonate and washed with diethyl ether (2×100 mL). The combined etheral layers were washed with saturated aqueous sodium chloride (2×50 mL), dried over MgSO 4, filtered and concentrated under reduced pressure to give a brown crystalline solid. The crude product was purified by chromatography (silica gel, pet. ether/ethyl acetate) to afford a yellow crystalline solid (935 mg, 32% yield), m.p. 94°-96° C.

후처리

  1. additionwas added in one portion
  2. additionwas added
  3. concentrationThe reaction mixture was concentrated to 100 mL
  4. additionthen diluted with diethyl ether (300 mL)
  5. extractionThe organic layer was extracted with 1N aqueous hydrochloric acid (100 mL)
  6. washwashed with diethyl ether (2×100 mL)
  7. washThe combined etheral layers were washed with saturated aqueous sodium chloride (2×50 mL)
  8. dry with materialdried over MgSO 4
  9. filtrationfiltered
  10. concentrationconcentrated under reduced pressure
  11. customto give a brown crystalline solid
  12. customThe crude product was purified by chromatography (silica gel, pet. ether/ethyl acetate)

출처 및 근거

ORD 기록
ord-0d08b817f39842429f317ec273a5f84a
출처 데이터셋
uspto-grants-1991_03
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US05001126

반응 노트

이 페이지에서참가 물질실험 절차후처리출처 및 근거반응 노트