홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

2-Fluorotoluene → 4-Fluoro-3-methylbenzaldehyde

HRID 379352
인쇄

반응식

HRID 379352 반응식
[Cl-].[Al+3].[Cl-].[Cl-].CC1C=C[C:9]([O:12]C)=CC=1.[F:14][C:15]1[CH:20]=[CH:19][CH:18]=[CH:17][C:16]=1[CH3:21]>Cl>[F:14][C:15]1[CH:20]=[CH:19][C:18]([CH:9]=[O:12])=[CH:17][C:16]=1[CH3:21]
참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트

참가 물질

5

반응물 3

HCID 72412-FluorotolueneHCID 77314-MethylanisoleHCID 6451240Aluminum(III) Chloride

생성물 1

HCID 27348744-Fluoro-3-methylbenzaldehyde수율 131.4%

시약·촉매·용매 1

HCID 313Hydrochloric Acid촉매

반응 조건

온도
30 °C

실험 절차

229.30 g of aluminum chloride (mol. wt. 133.34; 1,719.7 mmol), 110.0 g (4-Methylanisole (mol. Wt. 122.17; 900.4 mmol), and about 500 g of 2-fluorotoluene (mol. Wt. 110.13; 4,540.1 mmol) were charged to a 2 liter Parr®-brand 4522 stainless steel reaction vessel. To this mixture was added 5 drops of concentrated HCl. The vessel was sealed, heated to 30° C., and purged three times with carbon monoxide with the pressure of the vessel increased to 100 psi for each purging. After the third purge, the vessel was vented and a final introduction of CO was made at a pressure of about 550 psi, the pressure at which the reaction was maintained for the total reaction time of about 66 hours (the reaction temperature was maintained at 30° C. for the duration as well). Once the reaction was complete, the resultant mixture (exhibiting a greenish-brown color) was poured into about 500 mL of ice water (which turned the solution a yellow color), to which was added 500 mL of cyclohexane. The top, organic layer was removed and washed three times with water using a separatory funnel and dried over magnesium sulfate. The residual organic phase was then distilled under vacuum to remove excess cyclohexane, 2-fluorotoluene, and left about 98.01 g of 4-fluoro-3-methylbenzaldehyde product (mol. Wt. 138.14; 709.5 mmol; yield of approximately 86.7%). The 4-fluoro-3-methylbenzaldehyde product may then be easily separated from any residual 4-methylanisole by conversion into its corresponding bisulfite adduct, filtration, and decomposition of the bisulfite adduct under acidic or basic conditions.

후처리

  1. customThe vessel was sealed
  2. custompurged three times with carbon monoxide with the pressure of the vessel
  3. temperatureincreased to 100 psi for each purging
  4. customAfter the third purge
  5. temperaturethe pressure at which the reaction was maintained for the total reaction time of about 66 hours (the reaction temperature
  6. temperaturewas maintained at 30° C. for the duration as well)
  7. additionwas poured into about 500 mL of ice water (which
  8. additionwas added 500 mL of cyclohexane
  9. customThe top, organic layer was removed
  10. washwashed three times with water using a separatory funnel
  11. dry with materialdried over magnesium sulfate
  12. distillationThe residual organic phase was then distilled under vacuum
  13. customto remove excess cyclohexane, 2-fluorotoluene

출처 및 근거

ORD 기록
ord-e811511b02784d70b4757bd7de2e4fb3
출처 데이터셋
uspto-grants-2001_10
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US06297405B1

반응 노트

이 페이지에서참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트