홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Benzaldehyde → Methyl 3-hydroxy-3-phenylpropanoate

HRID 395903
인쇄

반응식

HRID 395903 반응식
C[Si](C)(C)Cl.[CH:6](=[O:13])[C:7]1[CH:12]=[CH:11][CH:10]=[CH:9][CH:8]=1.Br[CH2:15][C:16]([O:18][CH3:19])=[O:17].Cl>C(OC(C)C)(=O)C.[Zn]>[OH:13][CH:6]([C:7]1[CH:12]=[CH:11][CH:10]=[CH:9][CH:8]=1)[CH2:15][C:16]([O:18][CH3:19])=[O:17]
참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트

참가 물질

7

반응물 4

HCID 240BenzaldehydeHCID 313Hydrochloric AcidHCID 6397ChlorotrimethylsilaneHCID 60984Methyl bromoacetate

생성물 1

HCID 347841Methyl 3-hydroxy-3-phenylpropanoate

시약·촉매·용매 2

HCID 23994Zinc촉매
HCID 7915
Isopropyl Acetate
용매

반응 조건

온도
65 °C

실험 절차

At room temperature, a three-necked flask fitted with reflux condenser, internal thermometer, dropping funnel and stirrer was charged, under nitrogen protective gas, with 5.7 g of zinc powder (87 mmol) in 35 ml of isopropyl acetate. After 1.65 ml of trimethylchlorosilane (13 mmol) had been added, the mixture was heated at 65° C. for 30 min. Following cooling to 60° C., 6.2 g of benzaldehyde (58 mmol) were added and, over the course of 4 min, 10.6 g of methyl bromoacetate (70 mmol) were added dropwise at 55° C., the temperature being maintained at 55° C. by external cooling. The mixture was then stirred at 55° C. for 5 min and, after cooling to 0° C., acidified with 40 ml of 2 N hydrochloric acid to a pH of 1 and stirred for 30 min. Excess zinc was removed by filtration and the organic phase separated. The organic phase was then stirred at 0° C. with 40 ml of 0.5 N hydrochloric acid and finally washed with 20 ml of saturated sodium hydrogen carbonate solution. Following phase separation and drying over sodium sulfate, the solvent was distilled off under reduced pressure. Methyl 3-hydroxy-3-phenylpropionate was obtained in a yield of 8.9 g (85% of theory) with a boiling point of 76° C. (0.07 mbar).

후처리

  1. customAt room temperature, a three-necked flask fitted
  2. temperaturewith reflux condenser
  3. temperatureFollowing cooling to 60° C.
  4. additionwere added dropwise at 55° C.
  5. temperaturethe temperature being maintained at 55° C. by external cooling
  6. temperatureafter cooling to 0° C.
  7. stirringstirred for 30 min
  8. customExcess zinc was removed by filtration
  9. customthe organic phase separated
  10. stirringThe organic phase was then stirred at 0° C. with 40 ml of 0.5 N hydrochloric acid
  11. washfinally washed with 20 ml of saturated sodium hydrogen carbonate solution
  12. customFollowing phase separation
  13. dry with materialdrying over sodium sulfate
  14. distillationthe solvent was distilled off under reduced pressure

출처 및 근거

ORD 기록
ord-044fe6760ed146048d43d8e6d2cef5d7
출처 데이터셋
uspto-grants-2003_08
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US06605716B2

반응 노트

이 페이지에서참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트