홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Hydrochloric Acid → 9-Phenyl-9H-carbazole-3-boronic acid

HRID 40435
인쇄

반응식

HRID 40435 반응식
Br[C:2]1[CH:3]=[CH:4][C:5]2[N:6]([C:15]3[CH:20]=[CH:19][CH:18]=[CH:17][CH:16]=3)[C:7]3[C:12]([C:13]=2[CH:14]=1)=[CH:11][CH:10]=[CH:9][CH:8]=3.C([Li])CCC.[B:26](OC)([O:29]C)[O:27]C.Cl>CCCCCC.O1CCCC1>[C:7]1([N:6]2[C:5]3[CH:13]=[CH:14][C:2]([B:26]([OH:29])[OH:27])=[CH:3][C:4]=3[C:20]3[C:15]2=[CH:16][CH:17]=[CH:18][CH:19]=3)[CH:12]=[CH:11][CH:10]=[CH:9][CH:8]=1
참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트

참가 물질

7

반응물 4

HCID 313Hydrochloric AcidHCID 8470Trimethyl borateHCID 189426243-Bromo-9-phenylcarbazole2회HCID 178418339Butyllithium

생성물 1

HCID 513584509-Phenyl-9H-carbazole-3-boronic acid수율 86%

시약·촉매·용매 2

HCID 8028Tetrahydrofuran
용매
HCID 8058Hexane용매

반응 조건

온도
-80 °C

실험 절차

Into a 500 mL three-neck flask were put 10 g (31 mmol) of 3-bromo-9-phenyl-9H-carbazole, and the air in the flask was replaced with nitrogen. After the replacement, 150 mL of tetrahydrofuran (THF), which was a solvent, was put into the flask and 3-bromo-9-phenyl-9H-carbazole was dissolved. This solution was cooled down to −80° C. Into this solution was dropped 20 mL (32 mmol) of n-butyllithium (a 1.58 mol/L hexane solution) with a syringe. After the dropping, the solution was stirred at the same temperature for 1 hour. After the stirring, 3.8 mL (34 mmol) of trimethyl borate was added to the solution, and the solution was stirred for about 15 hours while the temperature of the solution was being raised to room temperature. After the stirring, about 150 mL of diluted hydrochloric acid (1.0 mol/L) was added to the solution, and then the solution was stirred for 1 hour. After the stirring, an organic layer is separated from the mixture, the aqueous layer was extracted from the mixture with ethyl acetate, and the extracted solution and the organic layer were combined and washed with saturated sodium bicarbonate. The combined organic layer was dried with magnesium sulfate. After the drying, the mixture was subjected to gravity filtration. The obtained filtrate was condensed to give an oily light brown substance. The obtained oily substance was dried under reduced pressure to give 7.5 g of a light brown solid, which was the object of the synthesis, in a yield of 86%. A synthesis scheme of Step 1 is shown in (a-1) given below.

후처리

  1. customInto a 500 mL three-neck flask were put
  2. dissolutionwas dissolved
  3. stirringthe solution was stirred for about 15 hours while the temperature of the solution
  4. temperaturewas being raised to room temperature
  5. stirringthe solution was stirred for 1 hour
  6. customAfter the stirring, an organic layer is separated from the mixture
  7. extractionthe aqueous layer was extracted from the mixture with ethyl acetate
  8. washwashed with saturated sodium bicarbonate
  9. dry with materialThe combined organic layer was dried with magnesium sulfate
  10. filtrationAfter the drying, the mixture was subjected to gravity filtration
  11. customcondensed
  12. customto give an oily light brown substance
  13. customThe obtained oily substance was dried under reduced pressure

출처 및 근거

ORD 기록
ord-2cc49488185849e9a929b4db54e8177d
출처 데이터셋
uspto-grants-2013_09
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US08530060B2

반응 노트

이 페이지에서참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트