홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Hydrochloric Acid → 4-[(6-chloro-1H-indazol-3-yl)amino]-4-oxo-2-butenoic acid

HRID 497585
인쇄

반응식

HRID 497585 반응식
[OH-].[Na+].[Cl:3][C:4]1[CH:12]=[C:11]2[C:7]([C:8]([NH:13][C:14](=[O:22])/[CH:15]=[CH:16]/[C:17]([O:19]CC)=[O:18])=[N:9][NH:10]2)=[CH:6][CH:5]=1.Cl.C(OCC)(=O)C>C(O)C.O1CCCC1.O>[Cl:3][C:4]1[CH:12]=[C:11]2[C:7]([C:8]([NH:13][C:14](=[O:22])[CH:15]=[CH:16][C:17]([OH:19])=[O:18])=[N:9][NH:10]2)=[CH:6][CH:5]=1
참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트

참가 물질

8

반응물 4

HCID 313Hydrochloric AcidHCID 8857Ethyl AcetateHCID 14798Sodium Hydroxide2회HCID 9994564Ethyl (2E) 4-[(6-chloro-1H-indazol-3-yl)amino]-4-oxo-2-butenoate

생성물 1

HCID 670427914-[(6-chloro-1H-indazol-3-yl)amino]-4-oxo-2-butenoic acid수율 61.2%

시약·촉매·용매 3

HCID 702
Ethanol
용매
HCID 962Water용매
HCID 8028Tetrahydrofuran용매

반응 조건

온도
50 °C

실험 절차

0.95 cm3 of 1N sodium hydroxide is added to 280 mg of ethyl (2E) 4-[(6-chloro-1H-indazol-3-yl)amino]-4-oxo-2-butenoate, described in Example 2, in 25 cm3 of ethanol. The reaction medium is then heated at 50° C. for two hours, followed by addition of a further 1 equivalent of 1N sodium hydroxide. The temperature is maintained at 50° C. for a further 30 minutes and the heating is then stopped. At about 20° C., the medium is neutralized with 1N hydrochloric acid and then concentrated under reduced pressure (2 kPa; 40° C.). The solid thus obtained is taken up in 25 cm3 of tetrahydrofuran, 50 cm3 of ethyl acetate and 25 cm3 of distilled water. The organic phase is washed with 30 cm3 of saturated aqueous sodium chloride solution and then dried over magnesium sulphate. The solution is filtered and evaporated under the conditions described previously. The residue is taken up in 10 cm3 of ethyl acetate and the insoluble material is then filtered off and rinsed with 5 cm3 of ethyl acetate and with 10 cm3 of diethyl ether and dried under reduced pressure (90 Pa; 50° C.). 155 mg of 4-[(6-chloro-1H-indazol-3-yl)amino]-4-oxo-2-butenoic acid (E form) are obtained in the form of a pale yellow solid melting at 260° C.

후처리

  1. temperatureThe temperature is maintained at 50° C. for a further 30 minutes
  2. customAt about 20° C.
  3. concentrationconcentrated under reduced pressure (2 kPa; 40° C.)
  4. customThe solid thus obtained
  5. washThe organic phase is washed with 30 cm3 of saturated aqueous sodium chloride solution
  6. dry with materialdried over magnesium sulphate
  7. filtrationThe solution is filtered
  8. customevaporated under the conditions
  9. filtrationthe insoluble material is then filtered off
  10. washrinsed with 5 cm3 of ethyl acetate and with 10 cm3 of diethyl ether
  11. customdried under reduced pressure (90 Pa; 50° C.)

출처 및 근거

ORD 기록
ord-95712e851186412c80fffa43e6abad18
출처 데이터셋
uspto-grants-2005_09
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US06949579B2

반응 노트

이 페이지에서참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트