홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.1
  1. 홈
  2. /반응

Oxygen → 2-Butene-1,4-diol diacetate

HRID 839132
인쇄

반응식

HRID 839132 반응식
O.O.[C:3]([O-:6])(=[O:5])[CH3:4].[Li+].[C:8]([O:11][C:12](=[O:14])[CH3:13])(=[O:10])[CH3:9].[CH2:15]=[CH:16][CH:17]=[CH2:18].O=O>C(O)(=O)C>[C:3]([O:6][CH2:15][CH:16]([O:11][C:8](=[O:10])[CH3:9])[CH:17]=[CH2:18])(=[O:5])[CH3:4].[C:3]([O:6][CH2:15][CH:16]=[CH:17][CH2:18][O:11][C:12](=[O:14])[CH3:13])(=[O:5])[CH3:4]
참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트

참가 물질

7

반응물 4

HCID 977Oxygen2회HCID 78451,3-ButadieneHCID 7918Acetic AnhydrideHCID 23666338Lithium acetate dihydrate

생성물 2

HCID 1404022-Butene-1,4-diol diacetateHCID 27350013,4-Diacetoxy-1-butene

시약·촉매·용매 1

HCID 176
Acetic Acid
용매

반응 조건

온도
140 °C

실험 절차

Another run was conducted employing the same apparatus as that used in Example I but in this run there was no source of halide in the catalyst system. The reactor was charged with 3.4 grams (20 millimoles) of ceric oxide, 7.6 grams (75 millimoles) of lithium acetate dihydrate, 50 ml of acetic acid, 25 ml of acetic anhydride, and 10.0 grams (185.2 millimoles) of butadiene charged from the vapor phase. The reactor was placed in an oil bath, pressured to 30 psig with oxygen and heated to 140° C. About one hour was required for the oil bath temperature to reach the reaction temperature desired, after which a reaction period of 5.3 hours was employed. During the reaction the reactor was pressured to 120 psig with oxygen intermittently. At the end of the reaction period (5.3 hours) the reactor was vented and 1.8 grams of unreacted butadiene was recovered in a cold trap. The reaction mixture was diluted with ether and 2.67 grams of a solid precipitate was collected by filtration and dried. The ether solution filtrate was washed with water, neutralized with sodium carbonate solution, dried over magnesium sulfate, filtered, and the ether then removed by distillation. The distillation residue (21.3 g) was a pale brown oil. It was analyzed by gas-liquid chromatography which showed that the residue was 86 percent ether with the remainder being the diacetoxy butenes. Specifically, there was produced 11 millimoles of 1,2-diacetoxy-3-butene and 3 millimoles of 1,4-diacetoxy-2-butene for a total yield of 14 millimoles of diacetoxy butenes which represents a yield of 7 percent bases on the butadiene charged.

후처리

  1. additioncharged from the vapor phase
  2. customThe reactor was placed in an oil bath
  3. customafter which a reaction period of 5.3 hours
  4. customDuring the reaction the reactor
  5. customAt the end of the reaction period (5.3 hours) the reactor
  6. custom1.8 grams of unreacted butadiene was recovered in a cold trap
  7. additionThe reaction mixture was diluted with ether and 2.67 grams of a solid precipitate
  8. filtrationwas collected by filtration
  9. customdried
  10. washThe ether solution filtrate was washed with water
  11. dry with materialdried over magnesium sulfate
  12. filtrationfiltered
  13. customthe ether then removed by distillation

출처 및 근거

ORD 기록
ord-0c1820ab70624ad7b45bb1ccbef8b8e0
출처 데이터셋
uspto-grants-1978_06
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US04093815

반응 노트

이 페이지에서참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트