StartseiteMCPWorkbenchSkills
StartseiteWorkbenchBenachrichtigungenMein Bereich
llms.txt · MCP-AnleitungDatenschutz · Nutzungsbedingungen · Supportv1.8.3
  1. Startseite
  2. /Reaktion

Iodine → 2-Fluoro-3-iodo-4-methylbenzonitrile

HRID 1668927
Drucken

Reaktionsgleichung

Reaktionsgleichung von HRID 1668927
CC1(C)CCCC(C)(C)N1.C([Li])CCC.[F:16][C:17]1[CH:24]=[C:23]([CH3:25])[CH:22]=[CH:21][C:18]=1[C:19]#[N:20].[I:26]I.[O-]S([O-])(=S)=O.[Na+].[Na+]>C1COCC1>[F:16][C:17]1[C:24]([I:26])=[C:23]([CH3:25])[CH:22]=[CH:21][C:18]=1[C:19]#[N:20]
KomponentenReaktionsbedingungenVersuchsvorschriftAufarbeitungQuellen und NachweiseNotizen zur Reaktion

Komponenten

7

Edukt 5

HCID 807IodineHCID 130352,2,6,6-TetramethylpiperidineHCID 24477Sodium ThiosulfateHCID 27784432-Fluoro-4-methylbenzonitrileHCID 178418339Butyllithium

Produkt 1

HCID 593838982-Fluoro-3-iodo-4-methylbenzonitrileAusbeute 48 %

Reagenzien, Katalysatoren, Lösungsmittel 1

HCID 8028TetrahydrofuranLösungsmittel3×

Reaktionsbedingungen

Temperatur
-50 °C

Versuchsvorschrift

A solution of 2,2,6,6,-tetramethylpiperidine (45 mL, 267 mmol) in THF (400 mL) was cooled below −80° C. under N2-atmosphere. n-Butyl lithium (2.5M in hexane, 110 mL, 275 mmol) was added slowly maintaining the temperature of the mixture below −70° C. After complete addition, the reaction mixture was warmed to −50° C. and stirred at this temperature for 30 minutes. The clear solution became turbid indicating the salt formation. It was cooled to −80° C. again and a solution of 2-fluoro-4-methylbenzonitrile (32.4 g, 240 mmol) in THF (150 mL) was slowly added taking care that the temperature of the reaction mixture remained below −70° C. It was then warmed up to −50° C. and stirred for 30 minutes. The mixture was then cooled to −70° C. and a saturated solution of I2 (67 g, 264 mmol) in THF was added slowly maintaining the temperature at −70° C. After complete addition, the mixture was warmed to ambient temperature. It was added to a solution of Na2S2O3 (160 g in 1.5 L of water) and stirred for an hour. The organic part was separated and the aqueous layer was extracted with EtOAc. The organic layers were combined and washed with brine. The organic layer was then dried over Na2SO4 and filtered. The volatiles were evaporated under reduced pressure. The crude product was subjected to vacuum distillation; at about 60° C., excess TMP was removed, at about 100° C., the starting compound 2-fluoro-4-methylbenzonitrile and a small amount of product was removed and, finally at 115° C., pure 2-fluoro-3-iodo-4-methylbenzonitrile was obtained (30 g, 48% yield). MS (M+H)+ 262.

Aufarbeitung

  1. temperaturemaintaining the temperature of the mixture below −70° C
  2. additionAfter complete addition
  3. temperatureIt was cooled to −80° C. again
  4. customremained below −70° C
  5. temperatureIt was then warmed up to −50° C.
  6. stirringstirred for 30 minutes
  7. temperatureThe mixture was then cooled to −70° C.
  8. temperaturemaintaining the temperature at −70° C
  9. additionAfter complete addition
  10. temperaturethe mixture was warmed to ambient temperature
  11. stirringstirred for an hour
  12. customThe organic part was separated
  13. extractionthe aqueous layer was extracted with EtOAc
  14. washwashed with brine
  15. dry with materialThe organic layer was then dried over Na2SO4
  16. filtrationfiltered
  17. customThe volatiles were evaporated under reduced pressure
  18. distillationThe crude product was subjected to vacuum distillation
  19. customat about 60° C., excess TMP was removed, at about 100° C.
  20. customthe starting compound 2-fluoro-4-methylbenzonitrile and a small amount of product was removed and, finally at 115° C.

Quellen und Nachweise

ORD-Eintrag
ord-77027c4a8c584ec2a2902a1389851475
Quelldatensatz
uspto-grants-2011_08
DOI
10.6084/m9.figshare.5104873.v1
Patentnummer
US07989461B2

Notizen zur Reaktion

Auf dieser SeiteKomponentenReaktionsbedingungenVersuchsvorschriftAufarbeitungQuellen und NachweiseNotizen zur Reaktion