StartseiteMCPWorkbenchSkills
StartseiteWorkbenchBenachrichtigungenMein Bereich
llms.txt · MCP-AnleitungDatenschutz · Nutzungsbedingungen · Supportv1.8.3
  1. Startseite
  2. /Reaktion

Methanesulfonyl chloride → 1-[Bis(4-chlorophenyl)methyl]-3-[(methylsulfonyl)(2-methoxycarbonylthien-5-yl)methylene] azetidine

HRID 25206
Drucken

Reaktionsgleichung

Reaktionsgleichung von HRID 25206
CC(C)([O-])C.[K+].[Cl:7][C:8]1[CH:13]=[CH:12][C:11]([CH:14]([C:20]2[CH:25]=[CH:24][C:23]([Cl:26])=[CH:22][CH:21]=2)[N:15]2[CH2:18][C:17](=O)[CH2:16]2)=[CH:10][CH:9]=1.[CH3:27][S:28]([CH2:31][C:32]1[S:36][C:35]([C:37]([O:39][CH3:40])=[O:38])=[CH:34][CH:33]=1)(=[O:30])=[O:29].CS(Cl)(=O)=O>O1CCCC1.C(OCC)C.O>[Cl:26][C:23]1[CH:22]=[CH:21][C:20]([CH:14]([C:11]2[CH:12]=[CH:13][C:8]([Cl:7])=[CH:9][CH:10]=2)[N:15]2[CH2:18][C:17](=[C:31]([S:28]([CH3:27])(=[O:29])=[O:30])[C:32]3[S:36][C:35]([C:37]([O:39][CH3:40])=[O:38])=[CH:34][CH:33]=3)[CH2:16]2)=[CH:25][CH:24]=1
KomponentenReaktionsbedingungenVersuchsvorschriftAufarbeitungQuellen und NachweiseNotizen zur Reaktion

Komponenten

8

Edukt 4

HCID 31297Methanesulfonyl chlorideHCID 17908444Methyl 5-(methylsulfonylmethyl)thiophene-2-carboxylateHCID 225066481-[Bis(4-chlorophenyl)methyl]azetidin-3-oneHCID 23665647Potassium tert-butoxide

Produkt 1

HCID 219551081-[Bis(4-chlorophenyl)methyl]-3-[(methylsulfonyl)(2-methoxycarbonylthien-5-yl)methylene] azetidine
Ausbeute 15,3 %

Reagenzien, Katalysatoren, Lösungsmittel 3

HCID 962WaterLösungsmittelHCID 3283Diethyl EtherLösungsmittelHCID 8028TetrahydrofuranLösungsmittel

Reaktionsbedingungen

Temperatur
-70 °C

Versuchsvorschrift

2.47 g of potassium tert-butoxide are added to a suspension of 6.12 g of 1-[bis(4-chlorophenyl)methyl]azetidin-3-one and 5.15 g of methyl 5-(methylsulfonylmethyl)thiophene-2-carboxylate in 200 cm3 of tetrahydrofuran, under an argon atomosphere, cooled to −70° C. The mixture is stirred for 1 hour 30 min at a temperature close to −70° C., and then 1.7 cm3 of methanesulfonyl chloride in solution in 8 cm3 of ethyl ether is added. After stirring for 1 hour at a temperature close to −70° C., the mixture is allowed to return to room temperature and then 80 cm3 of distilled water are added. The mixture is concentrated in a rotary evaporator to one third of its initial volume, and is then extracted with 500 cm3 of dichloromethane. The organic phase is washed with three times 80 cm3 of distilled water, dried over magnesium sulfate and concentrated to dryness under reduced pressure (2.7 kPa). The residue obtained is chromatographed on a silica gel column (particle size 0.02-0.04 mm, diameter 7.5 cm, height 35 cm), eluting at a nitrogen pressure of 0.5 bar with a cyclohexane and ethyl acetate mixture (70/30 by volume) and collecting 40 cm3 fractions. Fractions 19 to 29 are combined and then concentrated to dryness under reduced pressure (2.7 kPa). 1.6 g of 1-[bis(4-chlorophenyl)methyl]-3-[(methylsulfonyl)(2-methoxycarbonylthien-5-yl)methylene]azetidine are obtained in the form of a cream-colored foam [1H NMR spectrum (400 MHz, CDCl3, δ in ppm): 2.91 (s, 3H), 3.88 (s, 3H), 4.08 (mt, 2H), 4.37 (mt, 2H), 4.53 (s, 1H), from 7.25 to 7.45 (mt, 9H), 7.71 (d, J=3.5 Hz, 1H)].

Aufarbeitung

  1. customclose to −70° C.
  2. stirringAfter stirring for 1 hour at a temperature
  3. customclose to −70° C.
  4. customto return to room temperature
  5. concentrationThe mixture is concentrated in a rotary evaporator to one third of its initial volume
  6. extractionis then extracted with 500 cm3 of dichloromethane
  7. washThe organic phase is washed with three times 80 cm3 of distilled water
  8. dry with materialdried over magnesium sulfate
  9. concentrationconcentrated to dryness under reduced pressure (2.7 kPa)
  10. customThe residue obtained
  11. customis chromatographed on a silica gel column (particle size 0.02-0.04 mm, diameter 7.5 cm, height 35 cm)
  12. washeluting at a nitrogen pressure of 0.5 bar with a cyclohexane and ethyl acetate mixture (70/30 by volume)
  13. customcollecting 40 cm3 fractions
  14. concentrationconcentrated to dryness under reduced pressure (2.7 kPa)

Quellen und Nachweise

ORD-Eintrag
ord-cea6150bccfc44f7a7b0000eef19a9c8
Quelldatensatz
uspto-grants-2005_02
DOI
10.6084/m9.figshare.5104873.v1
Patentnummer
US06858603B2

Notizen zur Reaktion

Auf dieser SeiteKomponentenReaktionsbedingungenVersuchsvorschriftAufarbeitungQuellen und NachweiseNotizen zur Reaktion