StartseiteMCPWorkbenchSkills
StartseiteWorkbenchBenachrichtigungenMein Bereich
llms.txt · MCP-AnleitungDatenschutz · Nutzungsbedingungen · Supportv1.8.3
  1. Startseite
  2. /Reaktion

Iodoethane → 2-Ethyl-3-methoxybenzoic acid

HRID 260811
Drucken

Reaktionsgleichung

Reaktionsgleichung von HRID 260811
[CH3:1][O:2][C:3]1[CH:4]=[C:5]([C:9]2[O:10]C(C)(C)CN=2)[CH:6]=[CH:7][CH:8]=1.C([Li])C[CH2:18][CH3:19].C(I)C.[Cl-].[NH4+].[O:26]1CCCC1>Cl.O.CO>[CH2:18]([C:4]1[C:3]([O:2][CH3:1])=[CH:8][CH:7]=[CH:6][C:5]=1[C:9]([OH:10])=[O:26])[CH3:19]
KomponentenReaktionsbedingungenVersuchsvorschriftAufarbeitungQuellen und NachweiseNotizen zur Reaktion

Komponenten

9

Edukt 5

HCID 6340IodoethaneHCID 8028TetrahydrofuranHCID 25517Ammonium ChlorideHCID 22400605HCID 22400605, VerbindungHCID 178418339Butyllithium

Produkt 1

HCID 122472122-Ethyl-3-methoxybenzoic acid

Reagenzien, Katalysatoren, Lösungsmittel 3

HCID 313Hydrochloric AcidLösungsmittel2×
HCID 887MethanolLösungsmittel2×
HCID 962WaterLösungsmittel2×

Reaktionsbedingungen

Temperatur
-65 °C

Versuchsvorschrift

A 5 L, 4-necked round-bottom flask equipped with addition funnel, overhead stirring, and nitrogen purge was dried and charged with 128 g (623 mmoles) of 2-(3-methoxyphenyl)-5,5-dimethyloxazoline in 2.5 L of tetrahydrofuran. The mixture was cooled to -65° C. in a dry ice/isopropanol bath, and 450 mL of 1.6N n-butyl lithium was added slowly. After complete addition, the mixture was stirred for 1.5 hours at -45° to -30° C. After cooling to -45° C., ethyl iodide was added (80 mL, 1 mole). The temperature was maintained at -45° C. for 20 minutes, the mixture was allowed to warm to room temperature and was stirred overnight. Saturated ammonium chloride was added with ice cooling, and the mixture extracted several times with ether. The organic extracts were combined, dried over sodium sulfate, and solvent was removed in vacuo to give an oily solid. The solid was dissolved in 1 L of 6N hydrochloric acid in 3:1 water:methanol and heated at reflux for 15 hours. The hydrolysis was monitored by 1H NMR and shown to be about 75% complete. Additional acid was added (200 mL of 6N hydrochloric acid in 3:1 water:methanol), and the mixture was heated again at reflux for 8 hours. The mixture was cooled on ice, solids were collected, and dissolved in 10% aq. sodium hydroxide/methylene chloride. The aqueous layer was removed, acidified, and filtered to yield a tan solid which was air-dried at room temperature (53 g). An additional 23 g of product was obtained by further acidic hydrolysis of the methylene chloride extract. The melting point of the desired acid was 100°-101° C.

Aufarbeitung

  1. customA 5 L, 4-necked round-bottom flask equipped with addition funnel
  2. customnitrogen purge
  3. customwas dried
  4. additionAfter complete addition
  5. stirringthe mixture was stirred for 1.5 hours at -45° to -30° C
  6. temperatureAfter cooling to -45° C.
  7. temperatureThe temperature was maintained at -45° C. for 20 minutes
  8. temperatureto warm to room temperature
  9. stirringwas stirred overnight
  10. extractionthe mixture extracted several times with ether
  11. dry with materialdried over sodium sulfate, and solvent
  12. customwas removed in vacuo
  13. customto give an oily solid
  14. temperatureat reflux for 15 hours
  15. temperaturethe mixture was heated again
  16. temperatureat reflux for 8 hours
  17. temperatureThe mixture was cooled on ice, solids
  18. customwere collected
  19. dissolutiondissolved in 10% aq. sodium hydroxide/methylene chloride
  20. customThe aqueous layer was removed
  21. filtrationfiltered
  22. customto yield a tan solid which
  23. customwas air-dried at room temperature (53 g)

Quellen und Nachweise

ORD-Eintrag
ord-de00066a73fb41adb60de7197e12c816
Quelldatensatz
uspto-grants-1996_06
DOI
10.6084/m9.figshare.5104873.v1
Patentnummer
US05530028

Notizen zur Reaktion

Auf dieser SeiteKomponentenReaktionsbedingungenVersuchsvorschriftAufarbeitungQuellen und NachweiseNotizen zur Reaktion