Sodium Hydroxide
データを補完しています。しばらくしてからページを更新すると最新の内容を表示できます
1310-73-2[Na+].[OH-]HEMHJVSKTPXQMS-UHFFFAOYSA-MAt room temperature, sodium hydroxide is a white crystalline odorless solid that absorbs moisture from the air. It is a manufactured substance. When dissolved in water or neutralized with acid it liberates substantial heat, which may be sufficient to ignite combustible materials. Sodium hydroxide is very corrosive. It is generally used as a solid or a 50% solution. Other common names include caustic soda and lye. Sodium hydroxide is used to manufacture soaps, rayon, paper, explosives, dyestuffs, and petroleum products. It is also used in processing cotton fabric, laundering and bleaching, metal cleaning and processing, oxide coating, electroplating, and electrolytic extracting. It is commonly present in commercial drain and oven cleaners.
Other Classes -> Bases
Corrosives
Cosmetics ingredient -> Base; Buffering/pH Adjusting; Bulking/Viscosity; Conditioning/Emollient; Emulsifier; Flavor; Fragrance; Opacifying Agent; Other (Specify); Preservative/Stabilizer; Solvent
Cosmetic ingredients (Sodium Hydroxide) -> CIR (Cosmetic Ingredient Review)
Buffering; Denaturant
Strongly alkaline (1 % solution)
pH of a 0.05% wt/wt solution about 12; 0.5% solution about 13; 5% solution about 14
Herbicides
Active substance -> EU Pesticides database: Not approved
安全情報は参考情報です。供給元の安全データシート(SDS)、適用法令、専門家による評価に代わるものではありません。
Danger
H314: Causes severe skin burns and eye damage [Danger Skin corrosion/irritation]
P260, P264, P280, P301+P330+P331, P302+P361+P354, P304+P340, P305+P354+P338, P316, P321, P363, P405, and P501 (click each P-code to see the statement)
This chemical does not meet GHS hazard criteria for < 0.1% (4 of 6949) of reports.
Danger
H290 (47.5%): May be corrosive to metals [Warning Corrosive to Metals]
Chemical: Sodium hydroxide (Na(OH))
Hazard Traits - Dermatotoxicity; Ocular Toxicity; Respiratory Toxicity
Regulation (EC) No 1831/2003 (amended)
Sodium hydroxide (Na(OH)) is listed on the EPA's Chemical Data Reporting (CDR) system. Manufacturers and importers of Sodium hydroxide (Na(OH)) are required to report information about their production and use of this chemical to the EPA under the Toxic Substances Control Act (TSCA). (40 eCFR Part 711)
2004/129/EC
REACH registered substance: Sodium hydroxide (EC: 215-185-5)
Corrosive
Corrosive
Excerpt from ERG Guide 154 [Substances - Toxic and/or Corrosive (Non-Combustible)]:
Excerpt from ERG Guide 154 [Substances - Toxic and/or Corrosive (Non-Combustible)]:
· Non-combustible, substance itself does not burn but may decompose upon heating to produce corrosive and/or toxic fumes.
· Non-combustible, substance itself does not burn but may decompose upon heating to produce corrosive and/or toxic fumes.
· Non-combustible, substance itself does not burn but may decompose upon heating to produce corrosive and/or toxic fumes.
Because of its high-level alkalinity, sodium hydroxide in aqueous solution directly causes bond breakage in proteins (especially disulfide bridges). Hair and fingernails are found to be dissolved after 20 hours of direct contact with sodium hydroxide at pH values higher than 9.2. Sodium hydroxide has depilatory effects which have been described after accidental contact with solutions in the workplace. The breakage of bonds in proteins may lead to severe necrosis to the application site. The level of corrosion depends on the period of contact with the tissue, and on the concentration of sodium hydroxide.
Strong alkaline chemicals that destroy soft body tissues resulting in a deep, penetrating type of burn, in contrast to corrosives, that result in a more superficial type of damage via chemical means or inflammation. Caustics are usually hydroxides of light metals. SODIUM HYDROXIDE and potassium hydroxide are the most widely used caustic agents in industry. Medically, they have been used externally to remove diseased or dead tissues and destroy warts and small tumors. The accidental ingestion of products (household and industrial) containing caustic ingredients results in thousands of injuries per year.
There are no quantitative data for the absorption of sodium hydroxide through the skin. Solutions which contain 50 % sodium hydroxide have been shown to be corrosive and lethal when applied dermally to mice.
ALKALIS PENETRATE SKIN SLOWLY.
Ammonium hydroxide penetrates fastest, followed by sodium hydroxide, potassium hydroxide, and finally calcium hydroxide.
CIR ingredient: Sodium Hydroxide
読み込み中…
1310-73-2、81133-20-2DTXSID0029634CHEMBL2105794CHEBI:32145COLOR OR COLORING ADJUNCT, DOUGH STRENGTHENER, FLAVOR ENHANCER, FLAVORING AGENT OR ADJUVANT, FLOUR TREATING AGENT, FUMIGANT, OXIDIZING OR REDUCING AGENT, PH CONTROL AGENT, PROCESSING AID, WASHING OR SURFACE REMOVAL AGENT -> FDA Substance added to food
1.5 at 68 °F (USCG, 1999) - Denser than water; will sink
2.13 at 68 °F (USCG, 1999) - Denser than water; will sink
2.13 g/cu cm 25 °C
70-73 % solution: MP 62 °C; Density = 2.0 at 15.5 °C
2.1 g/cm³
2.13
White, orthogonal crystals
Colorless to white ... solid (flakes, beads, granular form).
Brittle, white, translucent crystalline solid
化学的特性Sodium hydroxide, NaOH,also referred to as caustic soda or sodium hydrate(and formerly known as lye), is a white,massive, deliquescent crystalline solid that is soluble in water,alcohol, and glycerol. It melts at 318°C (606 OF) and is the most widely used and available alkaline chemical. Most sodium hydroxide is produced as a coproduct of chlorine through the use of electrolytic cells;the cells are of the diaphragm, mercury, or membrane type. Some sodium hydroxide is marked as produced in the cells;most is evaporated and sold as 50% and 73% solutions or as anhydrous beads. Most caustic end uses require solutions of relatively low concentrations. Caustic soda is used as an analytical reagent and chemical intermediate, in scouring and cleaning baths,in rubber reclaiming and petroleum refining, in quenching baths for heat treating of steel,in cutting and soluble oils,in soaps and detergents, and in a wide variety of other applications.
化学性质强碱性物质,可以与酸性气体反应
· Non-combustible, substance itself does not burn but may decompose upon heating to produce corrosive and/or toxic fumes.
Causes severe burns of eyes, skin, and mucous membranes. (USCG, 1999)
Strong corrosive action on contacted tissues. INHALATION: dust may cause damage to upper respiratory tract and lung itself, producing from mild nose irritation to pneumonitis. INGESTION: severe damage to mucous membranes; severe scar formation or perforation may occur. EYE CONTACT: produces severe damage. (USCG, 1999)
· TOXIC and/or CORROSIVE; inhalation, ingestion or skin contact with material may cause severe injury or death.
· TOXIC and/or CORROSIVE; inhalation, ingestion or skin contact with material may cause severe injury or death.
· TOXIC and/or CORROSIVE; inhalation, ingestion or skin contact with material may cause severe injury or death.
· TOXIC and/or CORROSIVE; inhalation, ingestion or skin contact with material may cause severe injury or death.
At room temperature, sodium hydroxide is a white crystalline odorless solid that absorbs moisture from the air. It is a manufactured substance. When dissolved in water or neutralized with acid it liberates substantial heat, which may be sufficient to ignite combustible materials. Sodium hydroxide is very corrosive. It is generally used as a solid or a 50% solution. Other common names include caustic soda and lye. Sodium hydroxide is used to manufacture soaps, rayon, paper, explosives, dyestuffs, and petroleum products. It is also used in processing cotton fabric, laundering and bleaching, metal cleaning and processing, oxide coating, electroplating, and electrolytic extracting. It is commonly present in commercial drain and oven cleaners.
Liquid causes second or third degree burns after short contact; [CHRIS] In studies using rabbits, instillation by oral intubation caused within 10 seconds: erosion into the stomach muscle with 12% solutions; perforation with 28% solutions; and no damage with 1% solutions. Application to the skin of a 5% solution caused severe necrosis after 4 hours. Application of a 1% solution to the eyes caused no damage if the eyes were immediately irrigated. [ACGIH] Solutions > 30% are highly corrosive to skin. [Quick CPC] Inhalation of the aerosol can cause pulmonary edema. [ICSC]
1824 154
1823 154
1824 154
1823 154
1823 154(dry, solid)
1824 154(solution)
Substance added directly to human food affirmed as generally recognized as safe (GRAS).
Sodium hydroxide used as a general purpose food additive in animal drugs, feeds, and related products is generally recognized as safe when used in accordance with good manufacturing or feeding practice.
Bases, Strong
Bases, Strong
Excerpt from ERG Guide 154 [Substances - Toxic and/or Corrosive (Non-Combustible)]:
Excerpt from ERG Guide 154 [Substances - Toxic and/or Corrosive (Non-Combustible)]:
In case of fire in the surroundings, use appropriate extinguishing media.
Fresh air, rest. Refer immediately for medical attention.
Remove contaminated clothes. Rinse skin with plenty of water or shower for at least 15 minutes. Refer immediately for medical attention.
First rinse with plenty of water for several minutes (remove contact lenses if easily possible), then refer for medical attention.
Rinse mouth. Do NOT induce vomiting. If within a few minutes after ingestion, one small glass of water may be given to drink. Refer immediately for medical attention.
· CALL 911. Then call emergency response telephone number on shipping paper. If shipping paper not available or no answer, refer to appropriate telephone number listed on the inside back cover.
· ELIMINATE all ignition sources (no smoking, flares, sparks or flames) from immediate area.
· CALL 911. Then call emergency response telephone number on shipping paper. If shipping paper not available or no answer, refer to appropriate telephone number listed on the inside back cover.
· ELIMINATE all ignition sources (no smoking, flares, sparks or flames) from immediate area.
· CALL 911. Then call emergency response telephone number on shipping paper. If shipping paper not available or no answer, refer to appropriate telephone number listed on the inside back cover.
· ELIMINATE all ignition sources (no smoking, flares, sparks or flames) from immediate area.
(Act quickly)
Excerpt from NIOSH Pocket Guide for Sodium hydroxide:
General First Aid:
General First Aid:
General First Aid:
General First Aid:
· Wear positive pressure self-contained breathing apparatus (SCBA).
· Wear positive pressure self-contained breathing apparatus (SCBA).
· Wear positive pressure self-contained breathing apparatus (SCBA).
· Wear positive pressure self-contained breathing apparatus (SCBA).
Extinguish fire using agent suitable for surrounding fire. Use water spray to keep fire-exposed containers cool.
If material on fire or involved in fire: Extinguish fire using agent suitable for type of surrounding fire. (Material itself does not burn or burns with difficulty.) Use "alcohol" foam, dry chemical or carbon dioxide. Keep run-off water out of sewers and water sources.
CONTAINERS SHOULD BE STORED IN ROOMS WITH TRAPPED FLOOR DRAINS TOWARDS WHICH FLOORS SHOULD BE SLANTED. WHERE FLOOR DRAINS ARE NOT PROVIDED, CURBS OR DRAINED GUTTER, COVERED WITH ... GRILL, SHOULD BE CONSTRUCTED @ DOOR OPENINGS.
Volumetric sodium hydroxide soln used in laboratory must be protected from air to avoid formation of carbonate.
Store in a cool, dry, well-ventilated location. Separate from organic and oxidizing materials, acids, metal powders. Immediately remove and properly dispose of any spilled material.
On/in soil (solid): Construct barriers to convert or divert to impervious surface. Promptly shovel into steel containers.
Soil, Liquid: Absorb small amounts of spill with sand, vermiculite or other inert absorbant material; Shovel into steel containers. May also remove material with vacuum equipment.
Environment considerations - Land spill:: Dig a pit, pond, lagoon, or holding area to contain liquid or solid material. Dike surface flow using soil, sand bags, foamed polyurethane, or foamed concrete. Absorb bulk liquid with fly ash of cement powder.
Environmental considerations - Water spill: Use natural barriers or oil spill control booms to limit spill travel. Neutralize with dilute acid.
For more Cleanup Methods (Complete) data for SODIUM HYDROXIDE (6 total), please visit the HSDB record page.
Excerpt from ERG Guide 154 [Substances - Toxic and/or Corrosive (Non-Combustible)]:
Excerpt from ERG Guide 154 [Substances - Toxic and/or Corrosive (Non-Combustible)]:
SRP: The most favorable course of action is to use an alternative chemical product with less inherent propensity for occupational harm/injury/toxicity or environmental contamination. Recycle any unused portion of the material for its approved use or return it to the manufacturer or supplier. Ultimate disposal of the chemical must consider: the material's impact on air quality; potential migration in soil or water; effects on animal and plant life; and conformance with environmental and public health regulations.
Following neutralization either at the spill site or at a waste management facility, the resultant sludge can be disposed of in a secure landfill.
SRP: Wastewater from contaminant suppression, cleaning of protective clothing/equipment, or contaminated sites should be contained and evaluated for subject chemical or decomposition product concentrations. Concentrations shall be lower than applicable environmental discharge or disposal criteria. Alternatively, pretreatment and/or discharge to a permitted wastewater treatment facility is acceptable only after review by the governing authority and assurance that "pass through" violations will not occur. Due consideration shall be given to remediation worker exposure (inhalation, dermal and ingestion) as well as fate during treatment, transfer and disposal. If it is not practicable to manage the chemical in this fashion, it must be evaluated in accordance with EPA 40 CFR Part 261, specifically Subpart B, in order to determine the appropriate local, state and federal requirements for disposal.
Put into large vessel containing water. Neutralize with HCL /hydrochloric acid/. Discharge into the sewer with sufficient water. Recommendable methods: Neutralization & discharge to sewer. Peer review: Dilute greatly (< pH 9) before discharge. (Peer-review conclusions of an IRPTC expert consultation (May 1985))
Personal protection: chemical protection suit including self-contained breathing apparatus. Do NOT let this chemical enter the environment. Sweep spilled substance into covered plastic containers. Carefully collect remainder. Then store and dispose of according to local regulations.
An experimental study was conducted to investigate the effects of erythropoietin on the acute phase of esophageal burn damage induced by sodium hydroxide. A standard esophageal alkaline burn was produced by the application of 10% sodium hydroxide to the distal esophagus in an in vivo rat model. Fifty-six female rats were allocated into three groups: Group BC (baseline control, n = 8) rats were uninjured and untreated, Group PC (positive control, n = 24) rats were injured but untreated and Group EPO (erythropoietin-treated, n = 24) rats were injured and given subcutaneous erythropoietin (1,000 IU/kg per day), 15 min, 24, and 48 hr after administration of the NaOH solution. Six animals from Group PC and six from Group EPO were killed at 4, 24, 48, and 72 hr after application of NaOH to the esophagus. All of animals in Group BC were killed 4 hr after exposure to 0.9% NaCl. Oxidative damage was assessed by measuring levels of malondialdehyde (MDA) and nitric oxide (NO), and activities of superoxide dismutase (SOD) and catalase (CAT) in homogenized samples of esophageal tissue. Histologic damage to esophageal tissue was scored by a single pathologist blind to groups. MDA levels in the BC and EPO groups were significantly lower than those in the PC group (p < 0.05). CAT and SOD activities, and NO levels in the BC and EPO groups were significantly higher than in the PC group (p < 0.05). Esophageal tissue damage measured at 4, 24, 48, and 72 hr after NaOH application was significantly less in the EPO group than in the PC group (p < 0.05). When administered early after an esophageal burn induced by 10% sodium hydroxide in this rat model, erythropoietin significantly attenuated oxidative damage, as measured by biochemical markers and histologic scoring.
SRP4: Interacts with acid salts to form bases.
... Esophageal burns were induced in male rats by the administration of 10% sodium hydroxide. Lipid peroxidation (LPO) products were then measured at the following times: 0, 1, 6, 24, 48 and 72 hr after treatment. Tissue hydroxyproline (HP) concentrations in the injured area were assessed at 14 days after the administration of sodium hydroxide. The groups received either systemic melatonin or normal saline. There were two, non-ischemic, sham control groups treated with or without melatonin. LPO products, malondialdehyde (MDA) and 4-hydroxyalkenal (4-HDA), increased immediately after the administration of sodium hydroxide; this indicates the participation of free radicals in the development of damage. Melatonin diminished the oxidative response and the amount of HP in the late phase of the lesion. Melatonin reduced oxidative damage in the early phase of the esophageal burns induced by sodium hydroxide.
/SRP: Experimental/ The gastric damaging effects of necrotizing concn of sodium hydroxide were strongly reduced by paracetamol. ... Paracetamol might be protective by stimulating the biosynthesis of prostaglandins in the stomach wall.
For more Interactions (Complete) data for SODIUM HYDROXIDE (6 total), please visit the HSDB record page.
EC50; Species: Ceriodaphnia dubia (Water Flea) age <24 hr neonate; Conditions: freshwater, static, 23 °C; Concentration: 40380 ug/L for 48 hr (95% confidence interval: 34590-47130 ug/L); Effect: intoxication, immobilization /100% purity/
LC50; Species: Carassius auratus (Goldfish); Conditions: freshwater, static; Concentration: 160000 ug/L for 24 hr
LC100; Species: Cyprinus carpio; Concentration: 180 ppm for 24 hr at 25 °C /Conditions of bioassay not specified in source examined/
LC50; Species: Poecilia reticulata (Guppy) age 3-4 week young organisms; Conditions: saltwater, renewal, 24 °C, pH >9.8-<10.0, salinity 2.8%, dissolved oxygen > or =70% saturated; Concentration: 209000 ug/L for 24 hr (95% confidence interval: 153000-286000 ug/L) /98.6% purity/
For more Ecotoxicity Values (Complete) data for SODIUM HYDROXIDE (6 total), please visit the HSDB record page.
AQUATIC FATE: In the case of a solid, anhydrous sodium hydroxide spill on soil, ground water pollution will occur if precipitation occurs prior to clean up. Precipitation will dissolve some of the solid (with much heat given off) and create an aqueous solution of sodium hydroxide, which then would be able to infiltrate the soil. However, prediction of the concentration and properties of the solution produced would be difficult.
Serious local effects by all routes of exposure.
inhalation, ingestion, skin and/or eye contact
The CIR Expert Panel concluded that ... Sodium Hydroxide is safe in hair straighteners and depilatories under conditions of recommended use; users should minimize skin contact. These ingredients are safe for all other present practices of use and concentration described in this safety assessment when formulated to be nonirritating.
Safe for use in cosmetics, with qualifications
/AQUATIC SPECIES/ Concentration 20-100 mg/L in water kills some species of aquatic wildlife due to increase in pH.
/AQUATIC SPECIES/ Chronic exposure of guppies to sodium hydroxide (> or =25 mg/L) decreased their survival rate and weight gain, and caused either late or premature sexual maturity resulting in decreased fertility.
Cough. Sore throat. Burning sensation. Shortness of breath.
Redness. Pain. Serious skin burns. Blisters.
Redness. Pain. Blurred vision. Severe burns.
Abdominal pain. Burns in mouth and throat. Burning sensation in the throat and chest. Nausea. Vomiting. Shock or collapse.
irritation eyes, skin, mucous membrane; pneumonitis; eye, skin burns; temporary loss of hair
Estimated emissions of sodium hydroxide as one of the typical pollutants released from the synthetic organic chemical manufacturing industry (production/processing) may range from (unit process, product): alkylation, ethylbenzene, 1.9 to 21.5; condensation, polyethylene terephthalate, 0.065 to 23.1; dehydrogenation, isoprene, 0.5 to 19; dehydrohalogenation, vinylidene chloride, 45.5 to 605.5; polymerization, polyethylene terephthalate, 0.1 to 23.1 (all in g/kg produced)(1). The compound was spilled at an estimated 3,500 gallons into the Newark Bay on October 1991 from the Gist Brocades facility(2). Sodium hydroxide was involved in 2.6% of 6,928 chemical accidents in the US over a 5 year period up to 1985 at a reportable quantity of 2200 kg(3).
Substance added directly to human food affirmed as generally recognized as safe (GRAS).
Sodium hydroxide used as a general purpose food additive in animal drugs, feeds, and related products is generally recognized as safe when used in accordance with good manufacturing or feeding practice.
Residues of sodium hydroxide are exempted from the requirement of a tolerance when used in accordance with good agricultural practice as inert (or occasionally active) ingredients in pesticide formulations applied to growing crops or to raw agricultural commodities after harvest. Use: neutralizer. Limit: none.
Residues of sodium hydroxide are exempted from the requirement of a tolerance when used in accordance with good agricultural practice as inert (or occasionally active) ingredients in pesticide formulations applied to animals. Use: neutralizer. Limit: none.
The Agency has completed its review of all available information, and has determined that the data are sufficient to support reregistration of products containing sodium hydroxide. ... The Agency therefore finds that products containing sodium hydroxide as an active ingredient are eligible for reregistration. ... Although the Agency has found that certain products containing sodium hydroxide are eligible for registration, it should be understood that the Agency may take appropriate regulatory action, and/or require the submission of additional data to support the registration of products containing sodium hydroxide, if new information comes to the Agency's attention or if the data requirements for reregistration (or the guidelines for generating such data) change.
As the federal pesticide law FIFRA directs, EPA is conducting a comprehensive review of older pesticides to consider their health and environmental effects and make decisions about their continued use. Under this pesticide reregistration program, EPA examines newer health and safety data for pesticide active ingredients initially registered before November 1, 1984, and determines whether the use of the pesticide does not pose unreasonable risk in accordance to newer saftey standards, such as those described in the Food Quality Protection Act of 1996. Pesticides for which EPA had not issued Registration Standards prior to the effective date of FIFRA '88 were divided into three lists based upon their potential for human exposure and other factors, with List B containing pesticides of greater concern than those on List C, and with List C containing pesticides of greater concern than those on List D. Sodium hydroxide is found on List D. Case No: 4065; Pesticide type: fungicide, herbicide, antimicrobial; Case Status: RED Approved 09/92; OPP has made a decision that some/all uses of the pesticide are eligible for reregistration, as reflected in a Reregistration Eligibility Decision (RED) document .; Active ingredient (AI): sodium hydroxide; Data Call-in (DCI) Date(s): 09/30/92; AI Status: OPP has completed a Reregistration Eligibility Decision (RED) document for the case/AI.
Persons in charge of vessels or facilities are required to notify the National Response Center (NRC) immediately, when there is a release of this designated hazardous substance, in an amount equal to or greater than its reportable quantity of 1000 lb or 454 kg. The toll free number of the NRC is (800) 424-8802. The rule for determining when notification is required is stated in 40 CFR 302.4 (section IV.D.3.b).
Sodium hydroxide is designated as a hazardous substance under section 311(b)(2)(A) of the Federal Water Pollution Control Act and further regulated by the Clean Water Act Amendments of 1977 and 1978. These regulations apply to discharges of this substance. This designation includes any isomers and hydrates, as well as any solutions and mixtures containing this substance.
Used to neutralize acids, produce sodium salts, hydrolyze fats to make soaps, and precipitate metals; large amounts are used in petroleum refining, rayon production, and rubber reclaiming; [Merck Index # 8627] Also used in metal cleaning, electroplating, processing cotton fabrics, and bleaching; [ATSDR Medical Management] Used in photography (developing bath); [www.ci.tucson.az.us/arthazards/medium.html] In semiconductor manufacturing, sodium hydroxide is used to develop the pattern in the photoresists and also as a wet echant. [CHS, p. 44-5] Caustic soda is used in hide preparation for leather production; [PMID 21938525]
Acid and Alkali Cleaning of Metals [Category: Clean]
Textile arts [Category: Hobbies]
Both oil base and water base fracturing fluids are being used in the fracturing industry. Water base, which includes alcohol-water mixtures and low strength acids, make up the majority of treating fluids. The common chemicals added to these fluids are polymers for viscosity development, crosslinkers for viscosity enhancement, pH control chemicals, gel breakers for polymer degradation following the treatment, surfactants, clay stabilizers, alcohol, bactericides, fluid loss additives and friction reducer. /Hydraulic fracturing/
Hydraulic fracturing uses a specially blended liquid which is pumped into a well under extreme pressure causing cracks in rock formations underground. These cracks in the rock then allow oil and natural gas to flow, increasing resource production. ... Chemical Name: Sodium hydroxide; Chemical Purpose: Adjusts the pH of fluid to maintain the effectiveness of other components, such as crosslinkers; Product Function: pH Adjusting agent.
(1972) 1.1X10+12 GRAMS
(1975) 1.00X10+12 GRAMS
(1984) 1.14X10+12 g
1996: 2 million tons.
(1972) 9.53X10+10 GRAMS
(1975) 9.8X10+10 GRAMS
(1984) 4.78X10+11 g
1996: 540,000 tons
2023: 20,000,000,000 - <25,000,000,000 lb
(1972) 9.27X10+12 GRAMS
(1975) 8.7X10+12 GRAMS
(1985) 9.24X10+12 g
(1990) 24.06 billion lb
For more U.S. Production (Complete) data for SODIUM HYDROXIDE (12 total), please visit the HSDB record page.
51% IS CONSUMED IN CHEMICAL PROCESSING AND METAL PROCESSING OTHER THAN ALUMINUM; 6% FOR ALUMINUM PROCESSING; 18% IS USED IN PAPER AND PULP MANUFACTURE; 13% IS USED IN THE PETROLEUM, TEXTILE, SOAP, AND FOOD INDUSTRIES; 4% IS USED IN RAYON AND CELLOPHANE PRODUCTION; 8% IS USED IN OTHER APPLICATIONS (1974).
CHEMICAL PROFILE: Caustic soda. Organic Chemicals, 30%; Inorganic Chemicals, 20%; Pulp & Paper, 20%; Exports, 10%; Soaps and Detergents, 5%; Petroleum, 5%; Textiles, 4%; Alumina, 3%; Other, 3% (1986).
CHEMICAL PROFILE: Caustic soda. Pulp and paper, 22%; organic chemicals, 20%; inorganic chemicals, 11%; soaps and detergents, 7%; petroleum, 7%; water treatment, 7%; textiles, 5%; alumina, 4%; other, 9%; exports, 8%.
Direct application, 55% (pulp & paper, 24%; soaps and detergents, 10%; alumina, 6%; petroleum, 7%; textiles, 5%; water treatment, 5%; miscellaneous, 43%); organic chemicals 36% (propylene oxide, 23%; polycarbonates, 5%; ethyleneamines, 3%; epoxy resins, 3%; miscellaneous, 66%); inorganic chemicals, 9% (sodium/calcium hypochlorite, 24%; sulfur-containing compounds, 14%; sodium cyanide, 10%; miscellaneous 52%)
By reacting calcium hydroxide with sodium carbonate; from sodium chloride by electrolysis; from sodium metal and water vapor at low temperature.
Sodium hydroxide is produced industrially mainly by the electrolysis of sodium chloride. This yields sodium hydroxide solution, chlorine, and hydrogen in the mass ratios 1:0.88:0.025.
Solid sodium hydroxide (caustic soda) is obtained by evaporating sodium hydroxide solution until the water content is < 0.5 - 1.5 wt%. The most efficient utilization of energy is achieved with multistage equipment.
Causticization of sodium carbonate: A hot, ca. 12% solution of sodium carbonate is mixed with quicklime (CaO). The calcium carbonate that precipitates out is removed and the ca. 12% solution of sodium hydroxide is evaporated in several stages.
For more Methods of Manufacturing (Complete) data for SODIUM HYDROXIDE (6 total), please visit the HSDB record page.
Solid sodium hydroxide is supplied in the form of flakes, prills, cast blocks, and less commonly as tablets, briquettes, or granules.
Grades: commercial; ground; flake; beads; Food Chemical Codex grade; granulated (60% and 76% Na2O); rayon (low in iron, copper, and manganese); purified by alcohol (sticks, lumps, and drops); reagent; highest purity: CP, USP.
When kept in tight containers, the usual grades contain 97-98% sodium hydroxide.
Anhydrous (Rayon Grade) 99.0% minimum; Rayon Grade: 50% liquid; Regular Grade: 50% liquid, 47.7-51% purity.
For more Formulations/Preparations (Complete) data for SODIUM HYDROXIDE (8 total), please visit the HSDB record page.
Cosmetics product ingredient: Sodium hydroxide
Information on 1896 consumer products that contain Sodium hydroxide in the following categories is provided:
EPA Safer Chemical Functional Use Classes -> Processing Aids and Additives
Safer Chemical Classes -> Green circle - The chemical has been verified to be of low concern
Food additives
Fragrance Ingredients
Food Additives -> ACIDITY_REGULATOR -> JECFA Functional Classes
Food Additives -> ACIDITY_REGULATOR -> JECFA Functional Classes
解説純粋なものは無色透明な固体で,融点328 ℃.通常は少量の水と炭酸塩などを含む白色のもろい固体で,融点318.4 ℃,沸点1390 ℃.密度2.13 g cm-3.潮解性で,水には多量の熱を発して溶ける.水100 g に対する溶解度は42 g(0 ℃),109 g(20 ℃),347 g(100 ℃).エタノールに易溶,エーテル,アセトンに不溶.水溶液は強アルカリ性で濃厚なものは腐食性が強く,有機物を分解し皮膚をおかす.とくに眼に触れると失明のおそれがある.森北出版「化学辞典(第2版)
用途製薬、製剤原料。
用途酸の定量(容量分析)
用途試液調製、精密な酸中和剤(濃度が高すぎ、通常の容量分析にはほとんど用いられない)。
用途アミノ酸自動分析用調製液製造原料及び試料前処理試薬。
用途食品添加物。
用途一般分析用試液
用途化学繊維?紙?パルプ製造用,有機薬品?無機薬品?医薬?農薬?染料中間体製造用,グルタミン酸ソーダ原料,食品製造用
使用Sodium hydroxide is one of the most important industrial chemicals. In volume, it is in the top ten chemicals produced in the United States. It is used in manufacturing a large number of compounds including several sodium salts, in treating cellulose for producing rayon and cellophane, and in manufacturing soaps, detergents, pulp, and paper. Sodium hydroxide is a common neutralizing agent for acids in acid-base titrations and petroleum refining. Another major application is extracting metals from their ores where alkali fusion, such as fusion with caustic soda, often is applied to open the ores. Additionally, sodium hydroxide is used to precipitate metals as hydroxides. Other uses are in reclaiming rubber, dissolving casein in plastics production, refining vegetable oils, processing textiles, as an eluant in ion chromatography, etching and electroplating, and as a laboratory reagent. Sodium hydroxide also is used as a strong base in many organic synthesis and base-catalyzed reactions.
一般的な説明A white solid. Corrosive to metals and tissue. Used in chemical manufacturing, petroleum refining, cleaning compounds, drain cleaners.
Sodium hydroxide is manufactured by electrolysis of brine using inert electrodes. Chlorine is evolved as a gas at the anode and hydrogen is evolved as a gas at the cathode. The removal of chloride and hydrogen ions leaves sodium and hydroxide ions in solution. The solution is dried to produce the solid sodium hydroxide. A second method uses the Kellner–Solvay cell. Saturated sodium chloride solution is electrolyzed between a carbon anode and a flowing mercury cathode. In this case the sodium is produced at the cathode rather than the hydrogen because of the readiness of sodium to dissolve in the mercury. The sodium–mercury amalgam is then exposed to water and a sodium hydroxide solution is produced.
合成方法通常通过电解食盐水得到
定義本品は、ナトリウムの水酸化物であり、次の化学式で表される。
定義The most important commercial caustic.