이소부탄올

Excerpt from ERG Guide 129 [Flammable Liquids (Water-Miscible / Noxious)]:

Use water spray, powder, foam, carbon dioxide. In case of fire: keep drums, etc., cool by spraying with water.

Fresh air, rest.

Remove contaminated clothes. Rinse skin with plenty of water or shower.

First rinse with plenty of water for several minutes (remove contact lenses if easily possible), then refer for medical attention.

Rinse mouth. Give one or two glasses of water to drink. Do NOT induce vomiting. Refer for medical attention .

· CALL 911. Then call emergency response telephone number on shipping paper. If shipping paper not available or no answer, refer to appropriate telephone number listed on the inside back cover.

· ELIMINATE all ignition sources (no smoking, flares, sparks or flames) from immediate area.

· CALL 911. Then call emergency response telephone number on shipping paper. If shipping paper not available or no answer, refer to appropriate telephone number listed on the inside back cover.

· ELIMINATE all ignition sources (no smoking, flares, sparks or flames) from immediate area.

EYES: First check the victim for contact lenses and remove if present. Flush victim's eyes with water or normal saline solution for 20 to 30 minutes while simultaneously calling a hospital or poison control center. Do not put any ointments, oils, or medication in the victim's eyes without specific instructions from a physician. IMMEDIATELY transport the victim after flushing eyes to a hospital even if no symptoms (such as redness or irritation) develop.

General First Aid:

General First Aid:

(General first aid procedures)

· Wear positive pressure self-contained breathing apparatus (SCBA).

· Wear positive pressure self-contained breathing apparatus (SCBA).

1818.0 [ppm]

100.0 [ppm]

Use water spray, alcohol-resistant foam, dry chemical or carbon dioxide.

Wear self contained breathing apparatus for fire fighting if necessary.

Keep container tightly closed in a dry and well-ventilated place. Containers which are opened must be carfully resealed and kept upright to prevent leakage.

Keep away from heat and open flame.

1. Remove all ignition sources. 2. Ventilate area of spill or leak. For small quantities, absorb on paper towels. Evaporate in safe place ... allow sufficient time for evaporating vapors to completely clear hood ductwork. Burn paper in suitable location away from combustible materials. Large quantities can be collected & atomized in suitable combustion chamber.

Contain spillage, and then collect with an electrically protected vacuum cleaner or by wet-brushing and place in container for disposal according to local regulations.

Prevent further leakage or spillage if safe to do so. Do not let product enter drains. Discharge into the environment must be avoided.

Generators of waste (equal to or greater than 100 kg/mo) containing this contaminant, EPA hazardous waste number U140, must conform with USEPA regulations in storage, transportation, treatment and disposal of waste.

SRP: Wastewater from contaminant suppression, cleaning of protective clothing/equipment, or contaminated sites should be contained and evaluated for subject chemical or decomposition product concentrations. Concentrations shall be lower than applicable environmental discharge or disposal criteria. Alternatively, pretreatment and/or discharge to a permitted wastewater treatment facility is acceptable only after review by the governing authority and assurance that "pass through" violations will not occur. Due consideration shall be given to remediation worker exposure (inhalation, dermal and ingestion) as well as fate during treatment, transfer and disposal. If it is not practicable to manage the chemical in this fashion, it must be evaluated in accordance with EPA 40 CFR Part 261, specifically Subpart B, in order to determine the appropriate local, state and federal requirements for disposal.

Good candidate for liquid injection incineration, with a temperature range of 650 to 1600 °C, and a residence time of 0.1 to 2 seconds. Also, a good candidate for rotary kiln incineration, with a temperature range of 820 to 1600 °C, and a residence time of seconds. Additionally, a good candidate for fluidized bed incineration, with a temperature range of 450 to 980 °C, and a residence time of seconds. /From table/

... Atomizing in suitable combustion chamber.

For more Disposal Methods (Complete) data for ISOBUTYL ALCOHOL (6 total), please visit the HSDB record page.

Industrial exposure to mixed vapors of butyl acetate & isobutyl alcohol has caused vacuolar keratitis in several workers, but it is not known which of the substances was responsible.

Potentiation of carbon tetrachloride toxicity by aliphatic alcohols was measured by the elevation of serum glutamic oxalacetic transaminase activity. Ethanol, isopropyl alcohol, sec-butyl alcohol, and tert-butyl alcohol had a marked potentiating action. On an equimolar basis, sec-butyl alcohol and tert-butyl alcohol were more effective as potentiators than butyl alcohol and iso-butyl alcohol.

Metabolism in vivo of isobutanol, even in low concn, was markedly inhibited by simultaneous oxidation of ethanol.

Adding 1 g/l0 L of propan-1-ol, propan-2-ol, butan-1-ol, butan-2-ol, isobutanol to 40% ethanol in orange juice lowered and delayed blood ethanol max in 10 20-30 yr-old men who drank 3.75 mL/kg of synthetic beverage.

Nervous

Eyes, skin, respiratory system, central nervous system

EC50; Species: Scenedesmus subspicatus (Green Algae) exponential growth phase; Conditions: freshwater, static, 24 °C, pH 8.0-9.3; Concentration: 1250000 ug/L for 48 hr; Effect: population, decreased biomass /formulation/

EC50; Species: Scenedesmus subspicatus (Green Algae) exponential growth phase; Conditions: freshwater, static, 24 °C, pH 8.0-9.3; Concentration: 230000 ug/L for 48 hr; Effect: general population changes, decreased /formulation/

LC50; Species: Xenopus laevis (African Clawed Frog) age 3-4 wk; Conditions: freshwater, static, 20 °C; Concentration: 18300 ug/L for 48 hr /formulation/

LC50; Species: Rana catesbeiana (Bullfrog) weight 2.44 g; Conditions: freshwater, flow through, 17.1 (16.8-17.5) °C, pH 8.03 (8.00-8.06), hardness 196 mg/L CaCO3, alkalinity 172 mg/L CaCO3, dissolved oxygen 7.91 mg/L (7.54-8.16 mg/L); Concentration: 3010000 ug/L for 96 hr (95% confidence interval: 2820000-3210000 ug/L)

For more Ecotoxicity Values (Complete) data for ISOBUTYL ALCOHOL (19 total), please visit the HSDB record page.

TERRESTRIAL FATE: Based on a classification scheme(1), an estimated Koc value of 2.9(SRC), determined from a structure estimation method(2), indicates that isobutyl alcohol is expected to have very high mobility in soil(SRC). Volatilization of isobutyl alcohol from moist soil surfaces is expected to be an important fate process(SRC) given a Henry's Law constant of 9.78X10-6 atm-cu m/mole(3). Isobutyl alcohol is expected to volatilize from dry soil surfaces(SRC) based upon a vapor pressure of 10.4 mm Hg at 25 °C(4). Results of various biodegradation screening tests indicate that isobutyl alcohol is readily biodegradable(5). The biodegradation half-life of isobutyl alcohol was 2.4 days in a basic soil and 11.3 days in an acidic soil(6).

AQUATIC FATE: Based on a classification scheme(1), an estimated Koc value of 2.9(SRC), determined from a structure estimation method(2), indicates that isobutyl alcohol is not expected to adsorb to suspended solids and sediment(SRC). Volatilization from water surfaces is expected(3) based upon a Henry's Law constant of 9.78X10-6 atm-cu m/mole(4). Using this Henry's Law constant and an estimation method(3), volatilization half-lives for a model river and model lake are 3.3 and 27 days, respectively(SRC). According to a classification scheme(5), an estimated BCF of 3(SRC), from its log Kow of 0.76(6) and a regression-derived equation(2), suggests the potential for bioconcentration in aquatic organisms is low. Isobutyl alcohol is not expected to undergo hydrolysis in the environment due to the lack of functional groups that hydrolyze under environmental conditions(3). Results of various biodegradation screening tests indicate that isobutyl alcohol is readily biodegradable(7). In a river die-away test, isobutyl alcohol achieved 58% of its theoretical BOD in 5 days(8), suggesting biodegradation will be an important fate process in water(SRC).

ATMOSPHERIC FATE: According to a model of gas/particle partitioning of semivolatile organic compounds in the atmosphere(1), isobutyl alcohol, which has a vapor pressure of 10.4 mm Hg at 25 °C(2), is expected to exist solely as a vapor in the ambient atmosphere. Vapor-phase isobutyl alcohol is degraded in the atmosphere by reaction with photochemically-produced hydroxyl radicals(SRC). The half-life for the reaction in air with hydroxyl radicals is estimated to be 1.7 days(SRC), calculated from its measured rate constant of 9.2X10-12 cu cm/molecule-sec at 25 °C(3). Isobutyl alcohol does not contain chromophores that absorb at wavelengths >290 nm(4) and, therefore, is not expected to be susceptible to direct photolysis by sunlight(SRC).

Isobutyl alcohol was detected in beans at 72 ppb (average), split peas, 140 ppb (average) and lentils, 100 ppb (average)(1). Isobutyl alcohol was identified, not quantified, in volatiles from ripening bananas(2). Isobutyl alcohol was detected in Japanese beers at concentrations >1.5 ppm(3). Isobutyl alcohol was detected in soybeans at concentrations of 1,131.4 to 26,826.3 ug/kg(4). Isobutyl alcohol was identified, not quantified, in grain(5). Isobutyl alcohol was identified, not quantified, in volatiles from raw and roasted almonds(6). Isobutyl alcohol was identified in the skin and pulp of Queen Anne's melon at respective concentrations of 26.2 and 8.5 ug/kg(7).

Isobutanol has been identified as a volatile compound in the flavor component of fried chicken coated with 2% flour and fried in shortening consisting of 90% beef fat and 10% cotton seed oil. It is identified in apples, prickly pear pads, dried bonito, dried foliage of Cryptotaenia japonica and in gases volatilizing from potatoes in storage. Isobutanol is also found in most alcoholic beverages such as wine, distilled alcoholic beverages and various whiskeys at levels up to 1 g/L

The substance can be absorbed into the body by inhalation of its vapour and by ingestion.

inhalation, ingestion, skin and/or eye contact

IDENTIFICATION AND USE: Isobutyl alcohol is colorless, oily liquid with a penetrating, wine-like, disagreeable odor and sweet whiskey taste. Isobutyl alcohol is a solvent for surface coatings , adhesives, pharmaceuticals, pesticides, flavor, and fragrance. It is employed as an intermediate for synthetic resins. Not registered for current pesticide use in the U.S., but approved pesticide uses may change periodically and so federal, state and local authorities must be consulted for currently approved uses. HUMAN EXPOSURE AND TOXICITY: Isobutyl alcohol is rapidly absorbed following inhalation and dermal or oral exposures. In general, acute exposure to higher alcohols results primarily in CNS depression, hypotension, nausea, vomiting, and diarrhea. If aspirated, hemorrhagic pneumonitis may be noted. Eye exposure to vapors or liquid may result in burning, lacrimation, blurring of vision, and vacuoles in the cornea. There is a report of 3 cases with severe vertigo after handling butanol and isobutyl alcohol. ANIMAL STUDIES: Repeated inhalation by mice of 2125 ppm caused no deaths. Repeated exposures to moderate to high concentrations of isobutyl alcohol are well tolerated in rats. In a 90-day inhalation study, a reduced response to an external stimulus was noted in the exposed animals only during the exposure period. Repeated exposures did not exacerbate these transient effects. There was no evidence of neurotoxicity based on functional observational battery (FOB), quantitative motor activity, neuropathy and scheduled-controlled operant behavior endpoints. A 13-week oral gavage study conducted with isobutanol resulted in hypoactivity, ataxia and salivation in the 1,000 mg/kg bw/day dose groups. Hypoactivity and ataxia were resolved by the 4th week of the study. In addition, slight decreases in body weight gain and feed consumption were noted in the first two weeks of the 13-week study in the 1,000 mg/kg bw/day dose group. An inhalation, two-generation, reproductive toxicity study conducted with isobutyl alcohol (up to 2500 ppm) did not cause any parental systemic, reproductive, or neonatal toxicity when administered for two generations via whole-body exposure. In lifetime studies, rats given isobutyl alcohol by gavage or sc had increased incidences of total tumors including liver carcinomas, spleen sarcomas, proventricular carcinomas and myeloid leukemia, relative to controls. No adverse developmental effects were noted in rats or rabbits exposed by inhalation to 10,000 mg/cu m isobutyl alcohol during gestation. An increased rate of reverse mutation was demonstrated when Escherichia coli CA274 was treated with 0.7% isobutyl alcohol, without metabolic activation. In addition, isobutayl alcohol was negative in an in vivo mouse micronucleus study. ECOTOXICITY STUDIES: The lobster (Homarus americanus) was quickly and reproducibly anesthetized by the injection of isobutyl alcohol into the abdominal sinus. Isobutyl alcohol promoted cell elongation and increased total growth of wheat roots grown in white light; a higher concentration inhibited meristematic activity.

/AQUATIC SPECIES/ The lobster (Homarus americanus) was quickly and reproducibly anesthetized by the injection of 2-methyl-1-propanol into the abdominal sinus. The min effective (100%) dose was lower when the lobsters were held at 15 °C seawater (1.0 uL/10 g live weight) than when they were held at 6.0-8.5 °C (2.0 uL/10 g).

/PLANTS/ N-propanol, n-butanol, and isobutanol at 1x10-4 molar promoted cell elongation and increased total growth of wheat roots grown in white light; higher concentration inhibited meristematic activity.

Isobutyl alcohol is a food additive permitted for direct addition to food for human consumption as a synthetic flavoring substance and adjuvant in accordance with the following conditions: a) they are used in the minimum quantity required to produce their intended effect, and otherwise in accordance with all the principles of good manufacturing practice, and 2) they consist of one or more of the following, used alone or in combination with flavoring substances and adjuvants generally recognized as safe in food, prior-sanctioned for such use, or regulated by an appropriate section in this part.

Isobutyl alcohol is an indirect food additive for use only as a component of adhesives.

Isobutyl alcohol may be used in inks for marking food supplements in tablet form, gum, and confectionery. Restrictions: no residue.

U140; As stipulated in 40 CFR 261.33, when isobutyl alcohol, as a commercial chemical product or manufacturing chemical intermediate or an off-specification commercial chemical product or a manufacturing chemical intermediate, becomes a waste, it must be managed according to Federal and/or State hazardous waste regulations. Also defined as a hazardous waste is any residue, contaminated soil, water, or other debris resulting from the cleanup of a spill, into water or on dry land, of this waste. Generators of small quantities of this waste may qualify for partial exclusion from hazardous waste regulations (40 CFR 261.5).

Pursuant to section 8(d) of TSCA, EPA promulgated a model Health and Safety Data Reporting Rule. The section 8(d) model rule requires manufacturers, importers, and processors of listed chemical substances and mixtures to submit to EPA copies and lists of unpublished health and safety studies. 1-Propanol, 2-methyl is included on this list. Effective date: 3/7/86; Sunset date: 3/7/96.

Residues of isobutyl alcohol are exempted from the requirement of a tolerance when used in accordance with good agricultural practice as inert (or occasionally active) ingredients in pesticide formulations applied to growing crops only. Use: solvent.

This action promulgates standards of performance for equipment leaks of Volatile Organic Compounds (VOC) in the Synthetic Organic Chemical Manufacturing Industry (SOCMI). The intended effect of these standards is to require all newly constructed, modified, and reconstructed SOCMI process units to use the best demonstrated system of continuous emission reduction for equipment leaks of VOC, considering costs, non air quality health and environmental impact and energy requirements. Isobutanol is produced, as an intermediate or a final product, by process units covered under this subpart.

Persons in charge of vessels or facilities are required to notify the National Response Center (NRC) immediately, when there is a release of this designated hazardous substance, in an amount equal to or greater than its reportable quantity of 5000 lb or 2270 kg. The toll free number of the NRC is (800) 424-8802; The rule for determining when notification is required is stated in 40 CFR 302.4 (section IV. D.3.b).

Used as solvent in lacquers, paint removers, and liquid chromatography; used in organic synthesis; [ACGIH]

Painting (Solvents) [Category: Paint]

For Isobutyl alcohol (USEPA/OPP Pesticide Code: 001507) there are 0 labels match. /SRP: Not registered for current use in the U.S., but approved pesticide uses may change periodically and so federal, state and local authorities must be consulted for currently approved uses./

Isobutanol, a solvent for surface coatings & adhesives, is employed in lacquers, paint strippers, perfumes, cleaners & hydraulic fluid.

SOLVENT FOR SURFACE COATINGS & ADHESIVES; PROCESSING SOLVENT IN PHARMACEUTICAL, PESTICIDE, FLAVOR, & FRAGRANCE MFR; CHEM INT FOR ISOBUTYLAMINES, ZINC DIISOBUTYLDITHIOPHOSPHATE, ISOBUTYL ACETATE, ACRYLATE, METHACRYLATE ESTERS, ACRYLATE, & METHACRYLATE ESTERS; DILUENT-REACTANT IN THE ALKYLATION OF AMINO RESINS; COSOLVENT IN TERTIARY OIL RECOVERY

Isobutyl alcohol is used with dimethyl sulfoxide to prepare food additives such as sucrose fatty acid esters.

(1985) 1.60X10+10 g

(1987) 2.61X10+6 lb

(1988) 1.82X10+6 lb

(1985) 5.87X10+8 g

(1986) 1.08X10+6 lb

2023: 100,000,000 - <250,000,000 lb

(1993) 6.0292X10+7 kg

1-Propanol, 2-methyl- is listed as a High Production Volume (HPV) chemical (65FR81686). Chemicals listed as HPV were produced in or imported into the U.S. in >1 million pounds in 1990 and/or 1994. The HPV list is based on the 1990 Inventory Update Rule. (IUR) (40 CFR part 710 subpart B; 51FR21438).

Production volumes for non-confidential chemicals reported under the Inventory Update Rule.[Table#84]

Production volume for non-confidential chemicals reported under the 2006 Inventory Update Rule. Chemical: 1-Propanol, 2-methyl-. Aggregated National Production Volume: 100 to < 500 million pounds.

Non-confidential 2014 Chemical Data Reporting (CDR) information on the production and use of chemicals manufactured or imported into the United States. Chemical: 1-Propanol, 2-methyl-. National Production Volume: 172,360,823 lb/yr.

SOLVENT (EG, FOR SURFACE COATINGS & ADHESIVES & FOR PHARMACEUTICAL, PESTICIDE, FLAVOR & FRAGRANCE MFR), 26%; CHEM INT FOR ISOBUTYLAMINES, 22%; CHEM INT FOR ZINC DIISOBUTYLDITHIOPHOSPHATE, 17%; CHEM INT FOR ISOBUTYL ACETATE, 13%; CHEM INT FOR ACRYLATE & METHACRYLATE ESTERS, 4%; DILUENT-REACTANT IN PRODN OF AMINO RESINS, 4%; OTHER USES, 14% (1979)

... Produced by fermentation of carbohydrates.

From isobutylene; by reduction of isobutyraldehyde with sodium amalgam or in the presence of a catalyst; by fermentation of isobutyraldehyde.

Commercial isobutyl alcohol is made almost exclusively from the hydrogenation of isobutyraldehyde obtained by the hydroformylation of propylene. However, this alcohol is also commonly obtained as a coproduct in the Fischer Tropsch synthesis of methanol.

By-product of synthetic methanol production, purified by rectification.

For more Methods of Manufacturing (Complete) data for ISOBUTYL ALCOHOL (6 total), please visit the HSDB record page.

Cosmetics product ingredient: Isobutyl alcohol

Information on 17 consumer products that contain Isobutyl alcohol in the following categories is provided:

Fragrance Ingredients

Flavoring Agents -> JECFA Flavorings Index

Flavouring Agent -> FLAVOURING_AGENTFood Additives -> EXTRACTION_SOLVENT -> JECFA Functional Classes

Flavouring Agent -> FLAVOURING_AGENTFood Additives -> EXTRACTION_SOLVENT -> JECFA Functional Classes

Flavouring Agent -> FLAVOURING_AGENTFood Additives -> EXTRACTION_SOLVENT -> JECFA Functional Classes

Wholesale and Retail Trade

1-Propanol, 2-methyl-: ACTIVE