홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Hydrochloric Acid → HCID 178442263, 화합물

HRID 990272
인쇄

반응식

HRID 990272 반응식
[OH:1][C:2]1[C:3](=[O:13])[C:4]2[C:9]([C:10](=[O:12])[CH:11]=1)=[CH:8][CH:7]=[CH:6][CH:5]=2.Br[CH2:15][CH:16]=[C:17]([CH3:19])[CH3:18].[I-].[Na+].C(N(CC)CC)C.[OH-].[Na+].Cl>O.CS(C)=O>[CH3:18][C:17]([CH3:19])=[CH:16][CH2:15][C:11]1[C:10](=[O:12])[C:9]2[CH:8]=[CH:7][CH:6]=[CH:5][C:4]=2[C:3](=[O:13])[C:2]=1[OH:1]
참가 물질실험 절차후처리출처 및 근거반응 노트

참가 물질

9

반응물 6

HCID 313Hydrochloric AcidHCID 5238Sodium IodideHCID 8471TriethylamineHCID 14798Sodium HydroxideHCID 700922-Butene, 1-bromo-3-methyl-HCID 178516607HCID 178516607, 화합물

생성물 1

HCID 178442263HCID 178442263, 화합물

시약·촉매·용매 2

HCID 679Dimethyl Sulfoxide용매HCID 962Water용매

실험 절차

Into a dried 2,000 ml round bottomed flask was added 2-hydroxy-1,4-napthoquinone (69.7 g, 0.40 mol), 1-bromo-3-methyl-2-butene (66 g, 0.44 mol), sodium iodide (60 g, 0.4 mol), triethylamine (58.55 ml, 0.42 mol) and dimethylsulfoxide (DMSO), 500 ml. The mixture was stirred vigorously at room temperature under Argon atmosphere for 1 hour, then heated with a heating mantle to 45° C. After 3-6 hours, at 45° C. with vigorous stirring, the mixture was cooled down in an ice bath, and 800 ml of water was added to stop the reaction. The mixture is then transferred into a 2,000 ml separatory funnel and extracted three times with methylene chloride (500 ml, 300 ml and 200 ml). The organic phases were pooled and washed successively with water (800 ml), 5% aqueous sodium bicarbonate (2×800 ml)* and 1% aqueous sodium chloride (800 ml), then dried with sodium sulfate (50 g). After filtration, the filtrate was evaporated to dryness by Rotovap. The residue was dissolved in toluene (1,000 ml) with heating in a 50° C. water bath, and any insoluble material existing was filtered off. The warm toluene solution was extracted three times with freshly prepared, warm 2N sodium hydroxide (800 ml, 300 ml and 200 ml). The aqueous phases were pooled and neutralized by addition of hydrochloric acid (220 ml) with vigorous manual stirring, then extracted three times with toluene (500 ml, 300 ml and 300 ml). The organic phase were pooled and any black solid existing in the organic phases was removed by filtration. The combined organic phase was washed successively with 1% aqueous sodium chloride (800 ml), 5% aqueous sodium bicarbonate (500 ml) and 1% aqueous sodium chloride (800 ml), and then dried with sodium sulfate (50 g). After filtration, the filtrate was evaporated to dryness by Rotovap, then isopropanol (300 ml) was added for co-evaporation to completely remove residual toluene. The residue was dissolved in isopropanol (300 ml) with heating in an 80° C. water bath and then was cooled to 4° C. slowly. Pure lapachol was obtained after filtering, washing with cold isopropanol (4° C., 50-100 ml) and drying under vacuum.

후처리

  1. temperatureheated with a heating mantle to 45° C
  2. waitAfter 3-6 hours
  3. temperatureat 45° C. with vigorous stirring, the mixture was cooled down in an ice bath
  4. customthe reaction
  5. customThe mixture is then transferred into a 2,000 ml separatory funnel
  6. extractionextracted three times with methylene chloride (500 ml, 300 ml and 200 ml)
  7. washwashed successively with water (800 ml), 5% aqueous sodium bicarbonate (2×800 ml)* and 1% aqueous sodium chloride (800 ml)
  8. dry with materialdried with sodium sulfate (50 g)
  9. filtrationAfter filtration
  10. customthe filtrate was evaporated to dryness by Rotovap
  11. dissolutionThe residue was dissolved in toluene (1,000 ml)
  12. temperaturewith heating in a 50° C. water bath
  13. filtrationany insoluble material existing was filtered off
  14. extractionThe warm toluene solution was extracted three times
  15. customwith freshly prepared
  16. extractionextracted three times with toluene (500 ml, 300 ml and 300 ml)
  17. customwas removed by filtration
  18. washThe combined organic phase was washed successively with 1% aqueous sodium chloride (800 ml), 5% aqueous sodium bicarbonate (500 ml) and 1% aqueous sodium chloride (800 ml)
  19. dry with materialdried with sodium sulfate (50 g)
  20. filtrationAfter filtration
  21. customthe filtrate was evaporated to dryness by Rotovap
  22. additionisopropanol (300 ml) was added for co-evaporation to completely remove residual toluene
  23. dissolutionThe residue was dissolved in isopropanol (300 ml)
  24. temperaturewith heating in an 80° C. water bath
  25. temperaturewas cooled to 4° C. slowly

출처 및 근거

ORD 기록
ord-e0917fe6ff884368842ea6e58b37b5f0
출처 데이터셋
uspto-grants-2002_10
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US06458974B1

반응 노트

이 페이지에서참가 물질실험 절차후처리출처 및 근거반응 노트