HomeMCPWorkbenchSkills
HomeWorkbenchNotificationsMe
llms.txt · MCP GuidePrivacy Policy · Terms of Service · Supportv1.8.3
  1. Home
  2. /Reaction

Hydrochloric Acid → Tris(p-t-amylphenyl)phosphine

HRID 444431
Print

Reaction equation

HRID 444431 reaction equation
[Mg].Br[C:3]1[CH:8]=[CH:7][C:6]([C:9]([CH2:12][CH3:13])([CH3:11])[CH3:10])=[CH:5][CH:4]=1.P(Cl)(Cl)Cl.Cl.C(=O)([O-])[O-].[Na+].[Na+].[H][H].[P:27]>CO.O.C(Cl)(Cl)Cl.O1CCCC1>[C:9]([C:6]1[CH:7]=[CH:8][C:3]([P:27]([C:3]2[CH:4]=[CH:5][C:6]([C:9]([CH2:12][CH3:13])([CH3:10])[CH3:11])=[CH:7][CH:8]=2)[C:3]2[CH:4]=[CH:5][C:6]([C:9]([CH2:12][CH3:13])([CH3:10])[CH3:11])=[CH:7][CH:8]=2)=[CH:4][CH:5]=1)([CH2:12][CH3:13])([CH3:11])[CH3:10]
ParticipantsConditionsProcedureWorkupSources & evidenceReaction notes

Participants

12

Reactant 7

HCID 313Hydrochloric AcidHCID 10340Sodium CarbonateHCID 24387Phosphorus trichlorideHCID 5462224MagnesiumHCID 5462309PhosphorusHCID 129009891-Bromo-4-(2-methylbutan-2-yl)benzeneHCID 178418361HCID 178418361, compound

Product 1

HCID 12900990Tris(p-t-amylphenyl)phosphineYield 72%

Reagents, catalysts & solvents 4

HCID 887MethanolSolventHCID 962WaterSolvent2×HCID 6212ChloroformSolventHCID 8028TetrahydrofuranSolvent

Conditions

Temperature
15 °C

Procedure

A glass reactor equipped with a water-cooled reflux condenser, addition funnel, mechanically driven stirrer, thermometer and a nitrogen inlet was charged with 37 g (1.55 mole) of magnesium chips. A 30 cc portion of a solution containing 340.5 g (1.5 mole) of p-bromo-t-amylbenzene and one liter of tetrahydrofuran was added from the addition funnel with rapid stirring. When the reaction initiated, as indicated by an increase in the temperature of the reaction mixture, the remainder of the solution was added at a rate which maintained the reaction mixture at the boiling point without external heating. Following completion of the addition the reaction mixture was heated at the boiling point for two hours and allowed to cool to 15° C. A solution containing 68.8 g (0.5 mole) of phosphorus trichloride was then added at a rate which maintained the temperature of the reaction mixture at from 15° to 25° C. Following completion of the addition the reaction mixture was heated to the boiling point for two hours, allowed to cool and then poured with stirring into a mixture containing one liter of ice and 100 cc of concentrated aqueous hydrochloric acid. Stirring was continued until all of the ice melted, at which time sodium carbonate was gradually added until the pH of the solution was 7. One liter each of chloroform and water was added, the organic layer was separated and the water in this phase was removed using anhydrous magnesium sulfate. The chloroform was then removed by evaporation under the reduced pressure produced by a water aspirator to yield a yellow solid. This material was combined with a portion of methanol, pulverized and mixed thoroughly for one hour. The dried solid material weighed 170 g (72% yield), melted from 129.5° to 130° C. and was found to contain 83.3% carbon, 9.34% hydrogen and 6.50% phosphorus. The calculated values for the expected product are 83.9% carbon, 9.53% hydrogen and 6.57% phosphorus.

Workup

  1. temperaturecooled
  2. temperaturereflux
  3. additioncondenser, addition funnel
  4. additionwas added from the addition funnel with rapid stirring
  5. temperaturean increase in the temperature of the reaction mixture
  6. additionthe remainder of the solution was added at a rate which
  7. temperaturemaintained the reaction mixture at the boiling point without external heating
  8. additioncompletion of the addition the reaction mixture
  9. temperaturewas heated at the boiling point for two hours
  10. additionwas then added at a rate which
  11. temperaturemaintained the temperature of the reaction mixture at from 15° to 25° C
  12. additioncompletion of the addition the reaction mixture
  13. temperaturewas heated to the boiling point for two hours
  14. temperatureto cool
  15. additionpoured
  16. stirringStirring
  17. additionwas gradually added until the pH of the solution
  18. customthe organic layer was separated
  19. customthe water in this phase was removed
  20. customThe chloroform was then removed by evaporation under the reduced pressure
  21. customproduced by a water aspirator
  22. customto yield a yellow solid
  23. additionmixed thoroughly for one hour
  24. custommelted from 129.5° to 130° C.

Sources & evidence

ORD record
ord-8cb1b5700d2d429ebe329f23e25f8ffd
Source dataset
uspto-grants-1981_04
DOI
10.6084/m9.figshare.5104873.v1
Patent number
US04264593

Reaction notes

On this pageParticipantsConditionsProcedureWorkupSources & evidenceReaction notes