홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Hydrochloric Acid → 4-Methyl-6-phenylpyridazin-3(2H)-one

HRID 1479200
인쇄

반응식

HRID 1479200 반응식
[CH3:1][CH:2]1[CH2:7][C:6]([C:8]2[CH:13]=[CH:12][CH:11]=[CH:10][CH:9]=2)=[N:5][NH:4][C:3]1=[O:14].[Cl-].[Cl-].[Ca+2].Cl.[OH-].[Na+]>[Cu](Cl)Cl.[Cu]Cl.C(#N)C>[CH3:1][C:2]1[C:3](=[O:14])[NH:4][N:5]=[C:6]([C:8]2[CH:13]=[CH:12][CH:11]=[CH:10][CH:9]=2)[CH:7]=1
참가 물질실험 절차후처리출처 및 근거반응 노트

참가 물질

8

반응물 4

HCID 313Hydrochloric AcidHCID 14798Sodium HydroxideHCID 5284359Calcium ChlorideHCID 139013904-Methyl-6-phenyl-4,5-dihydropyridazin-3(2H)-one

생성물 1

HCID 833194-Methyl-6-phenylpyridazin-3(2H)-one수율 93.8%

시약·촉매·용매 3

HCID 24014
Cupric Chloride
촉매
HCID 62652Cuprous chloride촉매
HCID 6342Acetonitrile용매

실험 절차

7.0 g (35 mmole) of 2 is placed in a 250 ml single-necked round bottom flask followed by 30 mL of acetonitrile. The mixture is stirred to allow 2 to dissolve. 11.3 g (84 mole, 2.4 equiv.) of anhydrous copper (II) chloride is added to the solution to give a green-yellow suspension. A reflux condenser is connected to the flask and a dry tube filled with anhydrous CaCl2 is fitted to the top of the condenser. To control the HCl gas that forms during the course of the reaction, a NaOH solution is used to absorb the HCl that escapes from dry tube. The reaction mixture is heated to reflux, and the color of the reaction suspension changes to dark green upon heating. When the reaction is complete (after refluxing for 2 h), the flask is removed from the oil bath and cooled to ambient temperature. The reaction is cooled in an ice-water bath and 150 mL of ice-water is added to quench the reaction. The mixture is stirred vigorously for 10 minutes to give a gray precipitate and blue liquid containing copper (I) chloride. The precipitate is collected by filtration (pH of the filtrate is 0-1) and washed with 100 mL of 1N HCl solution, then 100 mL of water 5 times. To remove remaining copper by products that are trapped in the solid, the filter cake is stirred in 150 mL of 1N HCl solution for 0.5 h and filtered. The filter cake is subsequently washed with Milli-Q water until the filtrate is at pH 7 (approximately 7 washes). The solid is dried over a medium frit sintered glass funnel in vacuo to give 3 as a light gray powder in 93.8% yield. [See Eddy, S et al. Synthetic Communications, 2000, 30(1), 1-7.Csende, F et al. Synthesis, 1995, 1240-12420]

후처리

  1. dissolutionto dissolve
  2. customto give a green-yellow suspension
  3. customA reflux condenser is connected to the flask and a dry tube
  4. customis fitted to the top of the condenser
  5. customforms during the course of the reaction
  6. customto absorb the HCl that escapes
  7. customfrom dry tube
  8. temperatureThe reaction mixture is heated
  9. temperatureto reflux
  10. temperaturethe color of the reaction suspension changes to dark green upon heating
  11. temperature(after refluxing for 2 h)
  12. customthe flask is removed from the oil bath
  13. temperatureThe reaction is cooled in an ice-water bath
  14. addition150 mL of ice-water is added
  15. customto quench
  16. customthe reaction
  17. stirringThe mixture is stirred vigorously for 10 minutes
  18. customto give a gray precipitate and blue liquid
  19. filtrationThe precipitate is collected by filtration (pH of the filtrate
  20. washwashed with 100 mL of 1N HCl solution
  21. customTo remove
  22. stirringthe filter cake is stirred in 150 mL of 1N HCl solution for 0.5 h
  23. filtrationfiltered
  24. washThe filter cake is subsequently washed with Milli-Q water until the filtrate
  25. customThe solid is dried over a medium frit sintered glass funnel in vacuo

출처 및 근거

ORD 기록
ord-931bae64a2734d37ae12cb0143284337
출처 데이터셋
uspto-grants-2016_08
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US09408845B2

반응 노트

이 페이지에서참가 물질실험 절차후처리출처 및 근거반응 노트